Troy-Bilt 4510 warranty Assembly & Set-Up, Contents of Carton

Page 7

Assembly & Set-Up

3

Contents of Carton

•

One Snow Thrower

•

Two Replacement Auger Shear Pins

•

One Chute Assembly

•

One Snow Thrower Operator’s

•

One Briggs & Stratton Engine

•

One Product Registration Card

 

Manual

 

Operator’s Manual

 

 

Assembly

IMPORTANT: Two replacement auger shear pins are included with this manual (or stowed in the plastic handle panel). Refer to the Maintenance section for more information regarding shear pin replacement.

NOTE: All references in this manual to the left or right side of the snow thrower is from the operating position only. Exceptions, if any, will be specified.

IMPORTANT: This unit is shipped with the engine full of oil. After assembly, refer to the separate Engine Owner’s Manual included with this unit for fuel and oil fill-up details.

NOTE: Specifications are subject to change without notification or obligation. Images may not reflect your exact model and are for reference purposes only.

Handle

1.Remove any packaging material from the upper handle.

2.Remove the lower plastic wing nut, belleville washer and carriage bolt from each side of the upper handle; then raise the upper handle assembly until it snaps over the lower handle. See Figure 3-1.

Figure 3-1

3.Looking beneath the handle panel, check that all of the cables (steering, auger, and drive) are properly routed and not pinched or kinked. Make certain the springs at the lower end of the auger and drive cables are securely hooked into their respective actuator bracket.

4.Secure the upper handle and lower handle with the two wing nuts and carriage bolts removed earlier. Tighten the two wing nuts already installed in the upper holes to firmly secure the upper handle and support tubes. See Figure 3-2.

Figure 3-2

5.Align the upper and lower shift rods, then slide the shift rod connector down over the end of the lower shift rod. Tap the connector until the lower rod is completely through the connector. See Figure 3-3.

Figure 3-3

7

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operator’s Manual Record Product Information Table of ContentsTo The Owner Thank YouCalifornia Proposition Training Important Safe Operation PracticesPreparation Safe Handling of Gasoline OperationDo not modify engine Maintenance & StorageSpark Arrestor Symbol Safety SymbolsContents of Carton Assembly & Set-UpAssembly Chute Directional Control Chute AssemblySet-Up AdjustmentsAdjusting Drive and Auger Controls Testing Drive Control & Shift LeverGas & Oil Fill-Up Ignition Key Controls and FeaturesShift Lever Choke ControlOil Fill Electric Starter SwitchChute Assembly Primer BulbWheel Steering Controls Chute Clean-Out ToolTwo-Way Chute Control Chute Directional ControlElectric Starter OperationStarting The Engine Stopping The EngineOperating Tips Replacing Shear PinsTo Engage Drive To Engage AugersMaintenance Maintenance & AdjustmentsLubrication Augers Chute Bracket AdjustmentGear Case Auger ShaftAuger Control Drive ControlTire Pressure Belt Removal Preparation ServiceBelt Replacement Auger Belt ReplacementPulley Slot Changing Friction Wheel Drive Belt ReplacementService Short-Term Storage Off-Season StorageLong-Term Storage Problem Cause Remedy TroubleshootingComponent Replacement PartsPage Page MANUFACTURER’S Limited Warranty for

4510 specifications

The Troy-Bilt 4510 is a versatile and robust walk-behind mower designed to cater to both residential and small commercial lawn care needs. Known for its durability and efficiency, this mower has several features and technologies that make it a reliable choice for homeowners and professionals alike.

One of the standout features of the Troy-Bilt 4510 is its powerful engine. It is equipped with a robust 160cc engine that offers exceptional performance in various cutting conditions. The engine provides ample power to tackle thick grass and uneven terrain, ensuring a clean and even cut every time. The easy-start mechanism simplifies the ignition process, allowing users to get to mowing quickly without any hassle.

The 4510 also boasts a self-propulsion system with variable speed control, giving users the ability to adjust the pace of the mower according to their preferences and the mowing conditions. This feature is particularly beneficial when navigating tight corners or dealing with steep inclines, providing excellent maneuverability without sacrificing power.

Cutting height adjustment is another key characteristic of the Troy-Bilt 4510. With a simple lever adjustment, users can choose from multiple cutting height settings, allowing for personalized grass length options to suit different seasons or lawn types. This flexibility in cutting height ensures an aesthetically pleasing lawn year-round.

The mower's deck is designed for efficiency, featuring a 21-inch cutting width that allows it to cover more ground in less time while still providing precise cuts. The deck is often made from durable steel, ensuring longevity and resistance to wear and tear. Additionally, the Troy-Bilt 4510 features a mulch, bag, and side discharge capability, offering versatility in grass clipping management.

For user comfort, the mower comes with ergonomically designed handles that reduce fatigue during extended mowing sessions. The folding handle design makes storage easy, allowing the mower to occupy less space when not in use.

In summary, the Troy-Bilt 4510 is a feature-rich walk-behind mower that emphasizes power, ease of use, and adaptability. With its reliable engine, self-propulsion system, adjustable cutting height, and multiple clipping options, it is well-suited for homeowners who take pride in their lawns, as well as for professionals seeking efficient landscaping solutions. Whether tackling residential lawns or small commercial projects, the Troy-Bilt 4510 delivers performance and quality that users have come to expect from the Troy-Bilt brand.
Top Page Image Contents