Troy-Bilt 769-04090 Auger Control, Chute Assembly, Chute Bracket Adjustment, Retighten the nuts

Page 15

Skid Shoes

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes.

For close snow removal, as when using on a smooth concrete or asphalt driveway, place the skid shoes in the low position. Use the middle or high position when the area to be cleared is uneven. When operating on gravel, always put skid shoes in the high position.

See Figure 5-4.

Adjust skid shoes as follows:

1.Loosen, but do not remove, the hex flange locknuts which fasten the skid shoe to the auger housing.

2.Raise or lower the skid shoe to desired position.

3.Retighten the hex nuts loosened earlier.

NOTE: Make certain the bottom surface of skid shoe is flat against the ground to avoid uneven wear.

4. Repeat on the other side of the snow thrower.

Auger Control

Refer to instructions on page 9 to adjust the auger control. Make certain to check for correct adjustment as instructed before operating the snow thrower.

Chute Assembly

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to page 9 for instructions.

The remote chute control cables have been pre-adjusted at the factory. Move the remote chute lever on the control panel back and forward to adjust angle of the chute assembly.

Chute Bracket Adjustment

If the spiral at the bottom of the chute directional control is not fully engaging with the chute assembly, the chute bracket can be adjusted. To do so:

1.Loosen the two nuts which secure the chute bracket and reposition it slightly. See Figure 5-5.

2.Retighten the nuts.

Figure 5-4

Figure 5-5

5

Making

Adjustments

IMPORTANT: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing personal injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 769-04090 06/10/08 Two-Stage Snow ThrowerTable of Contents Finding and Recording Model NumberCustomer Support Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineAssembling Handle Setting Up Your Snow ThrowerItems Required For Assembly Loose PartsAttaching the Shift Rod Attaching the Chute AssemblyDrift Cutters If Equipped Lamp WiringClean-Out Tool Final AdjustmentsAuger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresChoke Control Operating Your Snow ThrowerKnow Your Snow Thrower This manual before Operating$26% #/.42 To Engage Augers Gas & Oil Fill-UpStopping The Engine To Engage DriveIf possible, remove snow immediately after it falls Always observe safety rules when performing any maintenanceOperating Tips General RecommendationsDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsMaintaining Your Snow Thrower LubricationReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltFriction Wheel Using a 3/4 wrench, hold the hex shaftChanging Friction Wheel Rubber Secure with the cupped washer and hex bolt removed earlierOff-Season Storage Problem Cause Remedy Trouble Shooting12.08.06 WarrantyFor parts and/or accessories refer to customer support on 6919 Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page Part RÉF Pièce Description Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page ’entretien conseils GarantieGarantie la annule Lubrification de etDépannage Solution Causes ProblèmeJours, 30 de plus pendant entreposé être doit moteur le Si PropreUse Accompagne qui moteur du d’utilisation notice la dansEntretien Frottement de Roue’essieu de Tout empêcher pour Et commandes lesPoulie la De Fente Moteur duBoulon l’autre retirez Éloignez’enlevez Tarière la de d’entraînement Courroie’engrenage LubrificationRoues Vitesse de mentRéglages Support de Des l’entraînement de CommandeVitesses de levier du Tige ’essieuLes de Évitez .65C 150F dépasser Général d’ordre Recommandations’utilisation Conseils Toucher’huile et d’essence Pleins Faites NeGoulotte la de dégagement de Outil Fonctions 2 à Roues des d’orientation CommandeGoulotte la de Commande Goulotte la de directionSouffleuse la de Commandes Tarière la de Commande TiquesPneuma Bandages pneus des Pression Pas Goulotte la de dégagement de OutilBien passe qu’il ce jusqu’à raccord le sur Tapez Vitesses de levier du tige la de InstallationGoulotte la de Installation «Réglages»Cisaillement de Boulons Goulotte la de manivelle la de MontageGuidon du Montage ’assemblage pour requis ArticlesGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de Durée’essence de Manipulation PréparationFormation VotreMachine la d’utiliser Sécurité de Symboles’utilisation La voir détachées Pièces Vente-après ServiceModèle de numéro le trouver Pour Matières des TablePhases deux neige à Souffleuse Ca.troybilt.www06/10/08

769-04090 specifications

The Troy-Bilt 769-04090 is a highly regarded product in the realm of outdoor power equipment, particularly recognized for its powerful performance and user-friendly features. This specific model is a rotary tiller, designed to help homeowners and gardening enthusiasts cultivate their soil effortlessly, making it an essential tool for creating the perfect garden bed.

One of the standout features of the Troy-Bilt 769-04090 is its robust 159cc OHV engine. This powerful engine ensures that the tiller can efficiently handle tough soil conditions, allowing for optimal tilling depth and ease in breaking ground. The engine is also designed for reliable start-up, often equipped with a recoil starting mechanism that promotes minimal frustration during operation.

Comfort and user-friendliness are at the forefront of the Troy-Bilt design philosophy. The tiller features adjustable, ergonomically designed handlebars that can be customized for various operator heights, helping to minimize fatigue during extended use. Additionally, the counter-rotating tines are a significant advantage, enabling users to break up hard-packed soil and mix soil amendments more effectively. This technology not only enhances tilling performance but also improves the overall efficiency of the tilling process.

The Troy-Bilt 769-04090 is equipped with a heavy-duty frame and durable tines that can withstand rigorous workloads, making it a long-lasting investment. The tiller's reinforced design contributes to stability during operation, allowing users to maneuver smoothly through their garden plots. The gear-driven transmission offers a choice of different speeds, giving the operator the flexibility to tackle various gardening tasks and adapt to the specific requirements of their soil.

Another noteworthy characteristic is the tiller’s easy-to-adjust tilling width and depth settings. This feature allows for customizable operation, so users can switch from preparing larger areas to focusing on smaller, sectioned-off garden plots with minimal hassle. The compact size of the Troy-Bilt 769-04090 makes it easy to transport and store, which is a significant advantage for those with limited storage space.

In summary, the Troy-Bilt 769-04090 combines powerful performance with user-friendly features, making it a prime choice for gardeners looking to streamline their soil preparation process. Its durable construction, comfortable operation, and versatile functionality contribute to an efficient and enjoyable gardening experience.
Top Page Image Contents