Troy-Bilt 769-04090 warranty Attaching the Chute Assembly, Attaching the Shift Rod

Page 7

Figure 3-4

Attaching the Chute Assembly

•Remove locknuts and screws securing one of the flange keepers to the chute assembly. See Figure 3-4.

•Loosen but do not remove the locknuts and screws on the other two flange keepers.

•Slide chute assembly over chute opening, making sure the flange keepers are beneath lip of chute adapter. The notches should engage with the spiral end of the chute crank. See Figure 3-5.

•Secure flange keeper, locknuts and screws previously removed. Tighten all flange keepers and hardware with two 7/16” wrenches. Do not over tighten.

NOTE: If necessary the chute crank support bracket can be adjusted so the spiral on the chute crank fully engages the teeth on the chute assembly. Refer to the Adjustment Section.

Attaching the Shift Rod

•Align the upper and lower shift rods, then slide the shift rod connector down over the end of the lower shift rod. Tap the connector until the lower rod is completely through the connector. See Figure 3-6.

NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or direction.

NOTE: If the full range of speeds (forward and reverse) cannot be achieved, refer to the Adjustment Section.

•Normally the cable ties holding the steering cables against the handle are loosely installed on each side of the lower handle at the factory. Pull the cable ties tight to secure. Cut the excess from the ends of cable ties.

•If not already attached, slip the cables that run from the handle panel to the discharge chute into the cable guide. See Figure 3-7.

3

Setting Up

Your Snow

Thrower

Figure 3-5

WARNING

Prior to operating your snow thrower, refer to Auger Control on page 9. Read and follow all instructions carefully and perform all adjustments to verify your unit is operating safely and properly.

Figure 3-6

Figure 3-7

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 769-04090 06/10/08 Two-Stage Snow ThrowerFinding and Recording Model Number Table of ContentsCustomer Support Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineAssembling Handle Setting Up Your Snow ThrowerItems Required For Assembly Loose PartsAttaching the Shift Rod Attaching the Chute AssemblyDrift Cutters If Equipped Lamp WiringClean-Out Tool Final AdjustmentsAuger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresChoke Control Operating Your Snow ThrowerKnow Your Snow Thrower This manual before Operating$26% #/.42 To Engage Augers Gas & Oil Fill-UpStopping The Engine To Engage DriveIf possible, remove snow immediately after it falls Always observe safety rules when performing any maintenanceOperating Tips General RecommendationsDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsLubrication Maintaining Your Snow ThrowerReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltFriction Wheel Using a 3/4 wrench, hold the hex shaftChanging Friction Wheel Rubber Secure with the cupped washer and hex bolt removed earlierOff-Season Storage Problem Cause Remedy Trouble Shooting12.08.06 WarrantyFor parts and/or accessories refer to customer support on 6919 Adressez-vous au «Service après-vente» Parts List Pièces DétachéesLa page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page Part RÉF Pièce Description Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page ’entretien conseils GarantieGarantie la annule Lubrification de etDépannage Solution Causes ProblèmeJours, 30 de plus pendant entreposé être doit moteur le Si PropreUse Accompagne qui moteur du d’utilisation notice la dansFrottement de Roue Entretien’essieu de Tout empêcher pour Et commandes lesPoulie la De Fente Moteur duBoulon l’autre retirez Éloignez’enlevez Tarière la de d’entraînement Courroie’engrenage LubrificationRoues Vitesse de mentRéglages Support de Des l’entraînement de CommandeVitesses de levier du Tige ’essieuLes de Évitez .65C 150F dépasser Général d’ordre Recommandations’utilisation Conseils ToucherFaites Ne ’huile et d’essence PleinsGoulotte la de dégagement de Outil Fonctions 2 à Roues des d’orientation CommandeGoulotte la de Commande Goulotte la de directionSouffleuse la de Commandes Tiques Tarière la de CommandePneuma Bandages pneus des Pression Pas Goulotte la de dégagement de OutilBien passe qu’il ce jusqu’à raccord le sur Tapez Vitesses de levier du tige la de InstallationGoulotte la de Installation «Réglages»Cisaillement de Boulons Goulotte la de manivelle la de MontageGuidon du Montage ’assemblage pour requis ArticlesGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de Durée’essence de Manipulation PréparationFormation VotreMachine la d’utiliser Sécurité de Symboles’utilisation La voir détachées Pièces Vente-après ServiceModèle de numéro le trouver Pour Matières des TableCa.troybilt.www Phases deux neige à Souffleuse06/10/08

769-04090 specifications

The Troy-Bilt 769-04090 is a highly regarded product in the realm of outdoor power equipment, particularly recognized for its powerful performance and user-friendly features. This specific model is a rotary tiller, designed to help homeowners and gardening enthusiasts cultivate their soil effortlessly, making it an essential tool for creating the perfect garden bed.

One of the standout features of the Troy-Bilt 769-04090 is its robust 159cc OHV engine. This powerful engine ensures that the tiller can efficiently handle tough soil conditions, allowing for optimal tilling depth and ease in breaking ground. The engine is also designed for reliable start-up, often equipped with a recoil starting mechanism that promotes minimal frustration during operation.

Comfort and user-friendliness are at the forefront of the Troy-Bilt design philosophy. The tiller features adjustable, ergonomically designed handlebars that can be customized for various operator heights, helping to minimize fatigue during extended use. Additionally, the counter-rotating tines are a significant advantage, enabling users to break up hard-packed soil and mix soil amendments more effectively. This technology not only enhances tilling performance but also improves the overall efficiency of the tilling process.

The Troy-Bilt 769-04090 is equipped with a heavy-duty frame and durable tines that can withstand rigorous workloads, making it a long-lasting investment. The tiller's reinforced design contributes to stability during operation, allowing users to maneuver smoothly through their garden plots. The gear-driven transmission offers a choice of different speeds, giving the operator the flexibility to tackle various gardening tasks and adapt to the specific requirements of their soil.

Another noteworthy characteristic is the tiller’s easy-to-adjust tilling width and depth settings. This feature allows for customizable operation, so users can switch from preparing larger areas to focusing on smaller, sectioned-off garden plots with minimal hassle. The compact size of the Troy-Bilt 769-04090 makes it easy to transport and store, which is a significant advantage for those with limited storage space.

In summary, the Troy-Bilt 769-04090 combines powerful performance with user-friendly features, making it a prime choice for gardeners looking to streamline their soil preparation process. Its durable construction, comfortable operation, and versatile functionality contribute to an efficient and enjoyable gardening experience.
Top Page Image Contents