Troy-Bilt 769-04090 warranty Auger Belt, Remove Loosen

Page 17

2.Remove the plastic belt cover, located near the engine, by removing the three self-tapping screws that secure it. See Figure 6-4.

3.a. Loosen the bolt shown in Figure 6-5 securing the

belt keeper bracket and remove the other bolt.

b.Push the belt keeper and bracket up off the engine pulley. See Figure 6-5.

Auger Belt

4.Remove the clip and flat washer from the ferrule in order to disconnect the auger idler rod from the brake bracket assembly. See Figure 6-6.

5.Slip the auger belt (the front belt) off the engine pulley.

6.Pull the brake bracket assembly towards the cable guide roller and unhook the auger cable “Z” fitting. See Figure 6-7.

7.From both sides of the the frame assembly, use a 1/2” wrench to remove the three hex tap screws securing the frame to the auger housing assembly. See Figure 6-8.

NOTE: Do not remove the lower hex flange lock nut on each side.

Figure 6-4

Remove

Loosen

Figure 6-5

Figure 6-6

Figure 6-7

Figure 6-8

6

Maintaining

Your Snow

Thrower

IMPORTANT

NEVER replace the auger shear pins with standard pins. Any damage to the auger gearbox or other com- ponents, as a result of doing so, will NOT be covered by your snow thrower’s warranty.

Check the condition of both auger belt and drive belt every 25 hours of snow thrower operation. Replace if either shows signs of wear and tear.

Specifications are subject to change without notification or obligation. Images may not reflect your exact model and are for refer- ence purposes only.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 769-04090 06/10/08 Two-Stage Snow ThrowerCustomer Support Table of ContentsFinding and Recording Model Number There are rotating blades inside Safety SymbolsDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useTraining Safe Operation PracticesPreparation Your ResponsibilityOperation Maintenance & StorageDo not modify engine Average Useful LifeItems Required For Assembly Setting Up Your Snow ThrowerLoose Parts Assembling HandleAttaching the Shift Rod Attaching the Chute AssemblyClean-Out Tool Lamp WiringFinal Adjustments Drift Cutters If EquippedSkid Shoes Check the adjustment of the auger control as followsTire Pressure Pneumatic Tires AugerKnow Your Snow Thrower Operating Your Snow ThrowerThis manual before Operating Choke Control$26% #/.42 Stopping The Engine Gas & Oil Fill-UpTo Engage Drive To Engage AugersOperating Tips Always observe safety rules when performing any maintenanceGeneral Recommendations If possible, remove snow immediately after it fallsMaking AdjustmentsShift Rod Drive ControlChute Bracket Adjustment Chute AssemblySee Figure Adjust skid shoes as follows Auger ControlReplacing Belts Maintaining Your Snow ThrowerLubrication Remove Loosen Auger BeltPulley Slot Drive BeltChanging Friction Wheel Rubber Using a 3/4 wrench, hold the hex shaftSecure with the cupped washer and hex bolt removed earlier Friction WheelOff-Season Storage Problem Cause Remedy Trouble Shooting12.08.06 WarrantyFor parts and/or accessories refer to customer support on 6919 La page 2 pour ce qui concerne les pièces et/ou accessoires Parts List Pièces DétachéesAdressez-vous au «Service après-vente» Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page Part RÉF Pièce Description Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page Garantie la annule GarantieLubrification de et ’entretien conseilsDépannage Solution Causes ProblèmeUse PropreAccompagne qui moteur du d’utilisation notice la dans Jours, 30 de plus pendant entreposé être doit moteur le Si’essieu de EntretienFrottement de Roue Poulie la De Fente Et commandes lesMoteur du Tout empêcher pour’enlevez ÉloignezTarière la de d’entraînement Courroie Boulon l’autre retirezRoues LubrificationVitesse de ment ’engrenageRéglages Vitesses de levier du Tige Des l’entraînement de Commande’essieu Support de’utilisation Conseils Général d’ordre RecommandationsToucher Les de Évitez .65C 150F dépasserGoulotte la de dégagement de Outil ’huile et d’essence PleinsFaites Ne Goulotte la de Commande Roues des d’orientation CommandeGoulotte la de direction Fonctions 2 àSouffleuse la de Commandes Pneuma Bandages pneus des Pression Tarière la de CommandeTiques Pas Goulotte la de dégagement de OutilGoulotte la de Installation Vitesses de levier du tige la de Installation«Réglages» Bien passe qu’il ce jusqu’à raccord le sur TapezGuidon du Montage Goulotte la de manivelle la de Montage’assemblage pour requis Articles Cisaillement de BoulonsResponsabilité Votre Remisage et EntretienMoyenne utile vie de Durée Gaz de émissions les concernant AvisFormation PréparationVotre ’essence de ManipulationMachine la d’utiliser Sécurité de SymbolesModèle de numéro le trouver Pour Vente-après ServiceMatières des Table ’utilisation La voir détachées Pièces06/10/08 Phases deux neige à SouffleuseCa.troybilt.www

769-04090 specifications

The Troy-Bilt 769-04090 is a highly regarded product in the realm of outdoor power equipment, particularly recognized for its powerful performance and user-friendly features. This specific model is a rotary tiller, designed to help homeowners and gardening enthusiasts cultivate their soil effortlessly, making it an essential tool for creating the perfect garden bed.

One of the standout features of the Troy-Bilt 769-04090 is its robust 159cc OHV engine. This powerful engine ensures that the tiller can efficiently handle tough soil conditions, allowing for optimal tilling depth and ease in breaking ground. The engine is also designed for reliable start-up, often equipped with a recoil starting mechanism that promotes minimal frustration during operation.

Comfort and user-friendliness are at the forefront of the Troy-Bilt design philosophy. The tiller features adjustable, ergonomically designed handlebars that can be customized for various operator heights, helping to minimize fatigue during extended use. Additionally, the counter-rotating tines are a significant advantage, enabling users to break up hard-packed soil and mix soil amendments more effectively. This technology not only enhances tilling performance but also improves the overall efficiency of the tilling process.

The Troy-Bilt 769-04090 is equipped with a heavy-duty frame and durable tines that can withstand rigorous workloads, making it a long-lasting investment. The tiller's reinforced design contributes to stability during operation, allowing users to maneuver smoothly through their garden plots. The gear-driven transmission offers a choice of different speeds, giving the operator the flexibility to tackle various gardening tasks and adapt to the specific requirements of their soil.

Another noteworthy characteristic is the tiller’s easy-to-adjust tilling width and depth settings. This feature allows for customizable operation, so users can switch from preparing larger areas to focusing on smaller, sectioned-off garden plots with minimal hassle. The compact size of the Troy-Bilt 769-04090 makes it easy to transport and store, which is a significant advantage for those with limited storage space.

In summary, the Troy-Bilt 769-04090 combines powerful performance with user-friendly features, making it a prime choice for gardeners looking to streamline their soil preparation process. Its durable construction, comfortable operation, and versatile functionality contribute to an efficient and enjoyable gardening experience.
Top Page Image Contents