Troy-Bilt 772C0772 warranty Safe Operation

Page 4

2

Safe

Operation

WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

TrainingPreparation

Practices

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol.

HEED ITS WARNING!

Your Responsibility Restrict the use

of this power machine to persons who read, understand

and follow the warnings and instructions

in this manual

and on the machine.

1.Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

2.Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.

3.Never allow children under 14 years old to operate this machine. Children 14 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.

4.Never allow adults to operate this machine without proper instruction.

5.Thrown objects can cause serious personal injury. Plan your snow-throwing pattern to avoid discharge of material toward roads, bystanders and the like.

6.Keep bystanders, helpers, pets and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

7.Exercise caution to avoid slipping or falling, especially when operating in reverse.

1.Thoroughly inspect the area where the equipment is to be used. Remove all doormats, newspapers, sleds, boards, wires and other foreign objects, which could be tripped over or thrown by the auger/impeller.

2.Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes.

3.Do not operate without wearing adequate winter outer garments. Do not wear jewelry, long scarves or other loose clothing, which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

4.Use a grounded three-wire extension cord and receptacle for all units with electric start engines.

5.Adjust collector housing height to clear gravel or crushed rock surfaces.

6.Disengage all control levers before starting the engine.

7.Never attempt to make any adjustments while engine is running, except where specifically recommended in the operator’s manual.

8.Let engine and machine adjust to outdoor temperature before starting to clear snow.

9.To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes, which can ignite. Wash your skin and change clothes immediately.

a.Use only an approved gasoline container.

b.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

c.Never fuel machine indoors.

d.Never remove gas cap or add fuel while the engine is hot or running.

e.Allow engine to cool at least two minutes before refuel- ing.

f.Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of filler neck to provide space for fuel expansion.

g.Replace gasoline cap and tighten securely.

h.If gasoline is spilled, wipe it off the engine and equip- ment. Move machine to another area. Wait 5 minutes before starting the engine.

i.Never store the machine or fuel container inside where there is an open flame, spark or pilot light (e.g. furnace, water heater, space heater, clothes dryer etc.).

j.Allow machine to cool at least 5 minutes before storing.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents OPERATOR’S Manual 772C0772 28/2005Table of Contents Chute Clean-out Tool Your Responsibility Restrict the useSafe Operation Operation Do not modify engineSetting Up Your Snow Thrower RecommendationsPivoting handle upward Lower handlePrior to operating Test onInstructions care Shear Pin Storage optionalDrift Cutters If Equipped All modelsClean-Out Tool Clean-Out ToolSkid Shoes Tire Pressure Pneumatic TiresOperating Your Snow Thrower Auger Control Drive Control/ Auger Control LockIgnition Key Four-Way Chute ControlElectric Starter If Equipped Starting The EngineElectric Starter Recoil StarterRecoil Starter Auger Control TestChute Control Shift CableDrive Control & Shift Lever Standard Skid Shoe Reversible Skid ShoeMaintaining Your Snow Thrower EngineLubrication Shave Plate and Skid ShoesAuger Belt Replacement Drive Belt Replacement AugersFriction Wheel Removal Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting TWO Year Supreme Warranty

772C0772 specifications

The Troy-Bilt 772C0772 is a versatile and reliable tool designed to tackle a variety of lawn care tasks with ease. This high-performance lawn mower is particularly appreciated by homeowners and landscapers alike for its robust design and advanced features that simplify yard maintenance.

One of the standout characteristics of the Troy-Bilt 772C0772 is its powerful engine. Equipped with a reliable 159cc OHV engine, this mower provides ample power to tackle tough grass types and uneven terrains. The engine’s air-cooled design ensures optimal performance and durability, allowing users to work efficiently even during extensive mowing sessions.

The cutting deck of the Troy-Bilt 772C0772 measures 21 inches, making it ideal for both large and small lawns. This size allows for excellent maneuverability while still covering substantial ground. The mower also features the innovative TriAction cutting system, which combines a unique blade design with a specially shaped deck. This results in a superior cut quality and effective grass clipping dispersion, leaving a clean finish on your lawn.

Another key feature of the Troy-Bilt 772C0772 is its adjustable cutting height. The mower allows users to choose from six different cutting positions, ranging from 1.25 to 3.75 inches. This level of customization enables homeowners to achieve their desired lawn height and adapt to varying grass conditions throughout the season.

The mower is also designed with user convenience in mind. It features an ergonomic handle that can be height adjusted, providing comfort while minimizing fatigue during operation. The 772C0772 integrates a robust steel frame and deck for enhanced durability, ensuring that it withstands demanding usage over the years.

Additionally, the Troy-Bilt 772C0772 is equipped with a reliable rear bagging system that captures grass clippings efficiently, keeping your lawn tidy. For those who prefer mulching, the mower comes with a mulching plug that enhances nutrient recycling back to the soil.

In summary, the Troy-Bilt 772C0772 is a powerful and efficient lawn mower that offers versatile functionality with its advanced engine, effective cutting system, and user-friendly design. It’s a solid choice for anyone looking to maintain a pristine lawn with minimal effort.
Top Page Image Contents