Troy-Bilt 31AE6GKF500 warranty Maintaining Your Snow Thrower, Engine, Lubrication, Augers

Page 16

6

Maintaining

Your Snow

Thrower

WARNING

Before lubricating, repairing, or inspect- ing, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop.

Keep all grease and oil off of the rubber friction wheel and aluminum drive plate.

Engine

Refer to the separate engine manual packed with your unit for all engine maintenance.

Lubrication

Engine

Refer to the separate engine manual packed with your unit for all engine lubrication instructions.

Gear Shaft

The gear (hex) shaft should be lubricated at least once a season or after every 25 hours of operation.

1.Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

2.Remove the lower frame cover by removing the two screws which secure it.

3.Apply a light coating of an all-weather multi-purpose oil to the hex shaft. See Figure 6-1.

NOTE: Avoid getting oil on rubber friction wheel and aluminum drive plate.

Wheels

At least once a season, remove both wheels. Clean and coat the axles with a multipurpose automotive grease before reinstalling wheels.

Chute Directional Control (optional)

Once a season, the joystick should be lubricated with petroleum jelly, linseed oil, mineral oil, paraffin wax or 3-in-1 oil.

Auger Shaft

At least once a season, remove the shear pins on auger shaft. Spray lubricant inside shaft, around the spacers. Also lubricate the flange bearings found at either end of the shaft. See Figure 6-2.

Augers

The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear. Refer to Figure 6-2.

If the augers will not turn, check to see if the pins have sheared. One set of replacement shear pins has been provided with the snow thrower. When replacing pins, spray an oil lubricant into shaft before inserting new pins.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary. To remove skid shoes:

1.Remove the four carriage bolts and hex flange nuts which secure them to the snow thrower.

2.Reassemble new skid shoes with the four carriage bolts (two on each side) and hex flange nuts. Refer to Figure 6-3.

 

Figure 6-1

 

3HEARE0IN

3PACERS

"EARING

 

 

 

Figure 6-2

 

Figure 6-3

To remove shave plate:

1.Remove the carriage bolts and hex nuts which attach it and the skid shoes to the snow thrower housing.

2.Reassemble new shave plate, making sure heads of carriage bolts are to the inside of housing. Tighten securely.

16

Image 16
Contents OPERATOR’S Manual Two-Stage Snow ThrowerFinding and Recording Model Number Table of ContentsCustomer Support Chute Clean-out Tool Your Responsibility Restrict the useSafe Operation Practices TrainingPreparation Your ResponsibilityMaintenance & Storage OperationDo not modify engine Average Useful LifeSetting Up Setting Up Your Snow Thrower Shear Pin Storage optionalSnowthrower Model Drift Cutters If EquippedAll models Clean-Out Tool Lamp Wiring Harness If equippedSkid Shoes Tire Pressure Pneumatic TiresOperating Your Snow Thrower $26% #/.42 Stopping The Engine Gas & Oil Fill-UpElectric Starter If Equipped To Engage Drive To Engage AugersRecoil Starter Auger Control TestMaking Adjustments Shift CableChute Control Drive Control & Shift LeverStandard Skid Shoe Reversible Skid ShoeMaintaining Your Snow Thrower EngineLubrication AugersRoll the auger belt off the engine pulley. See Figure Auger Belt ReplacementUnhook the support bracket spring from the frame Friction Wheel Inspection Drive Belt ReplacementRemove and replace belt in the reverse order Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 12.08.06OHV Part Description RÉF Pièce 30 in/po Remarque Lhabitacle peut être légèrement différent 5952Part Description RÉF Pièce 31AE6GKF500 Part Manual Chute Control Part Description RÉF Pièce Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Garantie FrottementSolution Causes Problème DépannageSouffleuse Propre etCarburant le Videz Gaz Régime ’entretienFrottement de roue la de Inspection Transmission de courroie la de Remplacement Ne Remarque Les RemarqueLa de courroie la de Remplacement Patins et plate LameTarière LubrificationTarière la de Commande RéglagesPatins Plastique en réversible Patins 4-5 FigureEt transmission la de Commande Goulotte la de CommandeVitesses de levier Vitesses de changement de CâbleSouffleuse MainToucher 150F dépasser’huile et d’essence Pleins Modèles certains sur électrique DémarreurModèles Certains sur électrique DémarreurTrans de commande la de Blocage La de proximité àSouffleuse la 33/-3.42Départ de Volet Souffleuse la de Commandes’essence plein le jamais faites Ne Général d’ordre Recommandations Goulotte la de dégagement de OutilPneumatiques Bandages pneus des Pression Goulotte la de dégagement de OutilÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage Inférieur Employer à moteur à l’huile à et carburant auQuant moteur du d’utilisation notice la consulter veuillez ’assemblage Après .ESSENCE Sans mais d’huile pleinMoyenne utile vie de Durée Remisage et EntretienGaz de émissions les concernant Avis Utilisation PréparationFormation Responsabilité VotreSécurité de Étiquettes De OutilVente-après Service Modèle de numéro le trouver PourMatières des Table SouffleusePhases deux neige à Souffleuse Ca.troybilt.www

31AE6GKF500 specifications

The Troy-Bilt 31AE6GKF500 is a versatile and efficient tiller designed to meet the needs of both novice and experienced gardeners. As a robust piece of equipment, it combines powerful performance with user-friendly features, making it a popular choice for those looking to cultivate their gardens with ease.

One of the standout features of the Troy-Bilt 31AE6GKF500 is its powerful engine. Equipped with a reliable 4-cycle engine, this tiller delivers ample torque and efficient fuel consumption, ensuring that users can tackle tough soil conditions without compromising on performance. The tiller's self-propelled design further enhances its usability, allowing users to navigate effortlessly through their garden beds while maintaining optimal control.

The Troy-Bilt 31AE6GKF500 features a sturdy set of rotatable tines that can reach a depth of up to 6 inches, making it suitable for various soil types and gardening tasks. These tines can be easily adjusted for width, allowing gardeners to customize their tilling experience based on the size of their garden. With a tilling width of 16 inches, this tiller can cover substantial ground, saving time and effort while preparing soil for planting.

User comfort is prioritized in the design of the Troy-Bilt 31AE6GKF500. It boasts an ergonomically designed handle that can be easily adjusted to accommodate different user heights, reducing fatigue during extended use. Additionally, the adjustable handlebar can be folded down for convenient storage, making it an ideal choice for those with limited space.

Another noteworthy characteristic of this tiller is its durable construction. Built with high-quality materials, the Troy-Bilt 31AE6GKF500 promises longevity, ensuring that it can withstand the rigors of frequent gardening tasks. Its compact design enhances its maneuverability, making it easy to operate in tight corners and small spaces.

Safety features are integral to the design of the Troy-Bilt 31AE6GKF500. The tiller comes equipped with a safety switch that prevents accidental starts, giving users peace of mind during operation.

In conclusion, the Troy-Bilt 31AE6GKF500 is an efficient and reliable tiller that caters to the needs of gardeners looking for a powerful and user-friendly gardening tool. With its robust engine, adjustable tines, ergonomic design, and safety features, it stands out as a top choice for both amateur and seasoned gardeners alike.