Troy-Bilt 31AE6GKF500 warranty Setting Up

Page 6

3

Setting Up

A

Your Snow

 

Thrower

B

NOTE: References to

 

right or left side of the

Figure 3-1

snow thrower are deter-

 

mined from behind the

 

unit in the operating

 

position.

 

NOTE: This Operator’s

 

Manual covers several

 

models, handle panels,

 

lights and chute cranks

 

are some features that

 

may vary by model.

 

Not all features refer-

 

enced in this manual

 

are applicable to all

 

snow thrower models.

Figure 3-2

NOTE: Two replace- ment auger shear pins are included with this manual (or stowed

in the plastic handle panel). Refer to Augers in the Maintainance Section for more information regarding shear pin replacement.

Figure 3-3

IMPORTANT: The snow thrower is shipped with oil and WITHOUT GASOLINE. After assembly, refer to separate engine manual for proper fuel and engine oil recommendations.

1.Observe the lower area of the snow thrower to be sure both cables are aligned with roller guides.

a.Pull up and back on upper handle as shown in Figure 3-1. Align upper handle with the lower handle.

b.Tighten hand knobs securing upper handle to lower handle.

2.Remove wing nut and hex screw from chute control assembly and clevis pin and cotter pin from chute support bracket. See Figure 3-2. Position the chute assembly (forward-facing) over the chute base.

3.Place chute assembly onto chute base and secure chute control assembly to chute support bracket with clevis pin and cotter pin removed earlier. See Figure 3-3.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents OPERATOR’S Manual Two-Stage Snow ThrowerTable of Contents Finding and Recording Model NumberCustomer Support Chute Clean-out Tool Your Responsibility Restrict the usePreparation Safe Operation PracticesTraining Your ResponsibilityDo not modify engine Maintenance & StorageOperation Average Useful LifeSetting Up Setting Up Your Snow Thrower Shear Pin Storage optionalDrift Cutters If Equipped Snowthrower ModelAll models Skid Shoes Clean-Out ToolLamp Wiring Harness If equipped Tire Pressure Pneumatic TiresOperating Your Snow Thrower $26% #/.42 Gas & Oil Fill-Up Stopping The EngineElectric Starter If Equipped Recoil Starter To Engage DriveTo Engage Augers Auger Control TestChute Control Making AdjustmentsShift Cable Drive Control & Shift LeverStandard Skid Shoe Reversible Skid ShoeLubrication Maintaining Your Snow ThrowerEngine AugersAuger Belt Replacement Roll the auger belt off the engine pulley. See FigureUnhook the support bracket spring from the frame Drive Belt Replacement Friction Wheel InspectionRemove and replace belt in the reverse order Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 12.08.06OHV Part Description RÉF Pièce 30 in/po Remarque Lhabitacle peut être légèrement différent 5952Part Description RÉF Pièce 31AE6GKF500 Part Manual Chute Control Part Description RÉF Pièce Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Garantie FrottementSolution Causes Problème DépannagePropre et SouffleuseCarburant le Videz Gaz ’entretien RégimeFrottement de roue la de Inspection Transmission de courroie la de Remplacement Ne Remarque Les RemarqueTarière La de courroie la de RemplacementPatins et plate Lame LubrificationPatins Tarière la de CommandeRéglages Plastique en réversible Patins 4-5 FigureVitesses de levier Et transmission la de CommandeGoulotte la de Commande Vitesses de changement de CâbleToucher SouffleuseMain 150F dépasserModèles ’huile et d’essence PleinsModèles certains sur électrique Démarreur Certains sur électrique DémarreurSouffleuse la Trans de commande la de BlocageLa de proximité à 33/-3.42Souffleuse la de Commandes Départ de Volet’essence plein le jamais faites Ne Pneumatiques Bandages pneus des Pression Général d’ordre RecommandationsGoulotte la de dégagement de Outil Goulotte la de dégagement de OutilÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage Quant moteur du d’utilisation notice la consulter veuillez InférieurEmployer à moteur à l’huile à et carburant au ’assemblage Après .ESSENCE Sans mais d’huile pleinRemisage et Entretien Moyenne utile vie de DuréeGaz de émissions les concernant Avis Formation UtilisationPréparation Responsabilité VotreSécurité de Étiquettes De OutilMatières des Table Vente-après ServiceModèle de numéro le trouver Pour SouffleusePhases deux neige à Souffleuse Ca.troybilt.www

31AE6GKF500 specifications

The Troy-Bilt 31AE6GKF500 is a versatile and efficient tiller designed to meet the needs of both novice and experienced gardeners. As a robust piece of equipment, it combines powerful performance with user-friendly features, making it a popular choice for those looking to cultivate their gardens with ease.

One of the standout features of the Troy-Bilt 31AE6GKF500 is its powerful engine. Equipped with a reliable 4-cycle engine, this tiller delivers ample torque and efficient fuel consumption, ensuring that users can tackle tough soil conditions without compromising on performance. The tiller's self-propelled design further enhances its usability, allowing users to navigate effortlessly through their garden beds while maintaining optimal control.

The Troy-Bilt 31AE6GKF500 features a sturdy set of rotatable tines that can reach a depth of up to 6 inches, making it suitable for various soil types and gardening tasks. These tines can be easily adjusted for width, allowing gardeners to customize their tilling experience based on the size of their garden. With a tilling width of 16 inches, this tiller can cover substantial ground, saving time and effort while preparing soil for planting.

User comfort is prioritized in the design of the Troy-Bilt 31AE6GKF500. It boasts an ergonomically designed handle that can be easily adjusted to accommodate different user heights, reducing fatigue during extended use. Additionally, the adjustable handlebar can be folded down for convenient storage, making it an ideal choice for those with limited space.

Another noteworthy characteristic of this tiller is its durable construction. Built with high-quality materials, the Troy-Bilt 31AE6GKF500 promises longevity, ensuring that it can withstand the rigors of frequent gardening tasks. Its compact design enhances its maneuverability, making it easy to operate in tight corners and small spaces.

Safety features are integral to the design of the Troy-Bilt 31AE6GKF500. The tiller comes equipped with a safety switch that prevents accidental starts, giving users peace of mind during operation.

In conclusion, the Troy-Bilt 31AE6GKF500 is an efficient and reliable tiller that caters to the needs of gardeners looking for a powerful and user-friendly gardening tool. With its robust engine, adjustable tines, ergonomic design, and safety features, it stands out as a top choice for both amateur and seasoned gardeners alike.
Top Page Image Contents