Troy-Bilt 31AE6GKF500 Off-Season Storage, Wipe equipment with an oiled rag to prevent rust

Page 19

Observe the following, when preparing your snow thrower for off-season storage:

•Drain fuel into an approved container outdoors, away from any open flame. Allow engine to cool. Extinguish cigarettes, cigars, pipes and other sources of ignition prior to draining fuel. Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

•If unit is to be stored over 30 days, prepare for storage as instructed in the separate engine manual packed with your unit.

•Run engine until fuel tank is empty and engine stops due to lack of fuel.

•Remove gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine.

•Drain carburetor by pressing upward on bowl drain, located below the carburetor cover.

•Fuel stabilizers, such as STA-BIL®, are an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Do not drain carburetor if using a fuel stabilizer.

•Wipe equipment with an oiled rag to prevent rust.

•Remove spark plug and pour one ounce of engine oil through spark plug hole into cylinder. Cover spark plug hole with rag. Crank engine several times to distribute oil. Replace spark plug.

•Follow the lubrication recommendations found in the Maintenance Section.

•Always store the snow thrower in a clean, dry area.

7

Off-Season

Storage

WARNING

Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance.

Drain fuel into an approved container outdoors, away from any open flame. Be certain engine is cool. Do not smoke. Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

Do not drain carburetor if using fuel stabilizer. Never use engine or carburetor cleaning products in the fuel tank or permanent damage may occur.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Two-Stage Snow Thrower OPERATOR’S ManualFinding and Recording Model Number Table of ContentsCustomer Support Your Responsibility Restrict the use Chute Clean-out ToolYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineSetting Up Shear Pin Storage optional Setting Up Your Snow ThrowerSnowthrower Model Drift Cutters If EquippedAll models Tire Pressure Pneumatic Tires Clean-Out ToolLamp Wiring Harness If equipped Skid ShoesOperating Your Snow Thrower $26% #/.42 Stopping The Engine Gas & Oil Fill-UpElectric Starter If Equipped Auger Control Test To Engage DriveTo Engage Augers Recoil StarterDrive Control & Shift Lever Making AdjustmentsShift Cable Chute ControlReversible Skid Shoe Standard Skid ShoeAugers Maintaining Your Snow ThrowerEngine LubricationRoll the auger belt off the engine pulley. See Figure Auger Belt ReplacementUnhook the support bracket spring from the frame Friction Wheel Inspection Drive Belt ReplacementRemove and replace belt in the reverse order Wipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting12.08.06 WarrantyOHV Part Description RÉF Pièce Remarque Lhabitacle peut être légèrement différent 5952 30 in/poPart Description RÉF Pièce 31AE6GKF500 Part Manual Chute Control Part Description RÉF Pièce Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Frottement GarantieDépannage Solution Causes ProblèmeSouffleuse Propre etCarburant le Videz Gaz Régime ’entretienFrottement de roue la de Inspection Transmission de courroie la de Remplacement Les Remarque Ne RemarqueLubrification La de courroie la de RemplacementPatins et plate Lame TarièrePlastique en réversible Patins 4-5 Figure Tarière la de CommandeRéglages PatinsVitesses de changement de Câble Et transmission la de CommandeGoulotte la de Commande Vitesses de levier150F dépasser SouffleuseMain ToucherCertains sur électrique Démarreur ’huile et d’essence PleinsModèles certains sur électrique Démarreur Modèles33/-3.42 Trans de commande la de BlocageLa de proximité à Souffleuse laDépart de Volet Souffleuse la de Commandes’essence plein le jamais faites Ne Goulotte la de dégagement de Outil Général d’ordre RecommandationsGoulotte la de dégagement de Outil Pneumatiques Bandages pneus des PressionÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage ’assemblage Après .ESSENCE Sans mais d’huile plein InférieurEmployer à moteur à l’huile à et carburant au Quant moteur du d’utilisation notice la consulter veuillezMoyenne utile vie de Durée Remisage et EntretienGaz de émissions les concernant Avis Responsabilité Votre UtilisationPréparation FormationDe Outil Sécurité de ÉtiquettesSouffleuse Vente-après ServiceModèle de numéro le trouver Pour Matières des TableCa.troybilt.www Phases deux neige à Souffleuse

31AE6GKF500 specifications

The Troy-Bilt 31AE6GKF500 is a versatile and efficient tiller designed to meet the needs of both novice and experienced gardeners. As a robust piece of equipment, it combines powerful performance with user-friendly features, making it a popular choice for those looking to cultivate their gardens with ease.

One of the standout features of the Troy-Bilt 31AE6GKF500 is its powerful engine. Equipped with a reliable 4-cycle engine, this tiller delivers ample torque and efficient fuel consumption, ensuring that users can tackle tough soil conditions without compromising on performance. The tiller's self-propelled design further enhances its usability, allowing users to navigate effortlessly through their garden beds while maintaining optimal control.

The Troy-Bilt 31AE6GKF500 features a sturdy set of rotatable tines that can reach a depth of up to 6 inches, making it suitable for various soil types and gardening tasks. These tines can be easily adjusted for width, allowing gardeners to customize their tilling experience based on the size of their garden. With a tilling width of 16 inches, this tiller can cover substantial ground, saving time and effort while preparing soil for planting.

User comfort is prioritized in the design of the Troy-Bilt 31AE6GKF500. It boasts an ergonomically designed handle that can be easily adjusted to accommodate different user heights, reducing fatigue during extended use. Additionally, the adjustable handlebar can be folded down for convenient storage, making it an ideal choice for those with limited space.

Another noteworthy characteristic of this tiller is its durable construction. Built with high-quality materials, the Troy-Bilt 31AE6GKF500 promises longevity, ensuring that it can withstand the rigors of frequent gardening tasks. Its compact design enhances its maneuverability, making it easy to operate in tight corners and small spaces.

Safety features are integral to the design of the Troy-Bilt 31AE6GKF500. The tiller comes equipped with a safety switch that prevents accidental starts, giving users peace of mind during operation.

In conclusion, the Troy-Bilt 31AE6GKF500 is an efficient and reliable tiller that caters to the needs of gardeners looking for a powerful and user-friendly gardening tool. With its robust engine, adjustable tines, ergonomic design, and safety features, it stands out as a top choice for both amateur and seasoned gardeners alike.
Top Page Image Contents