Troy-Bilt 31AE6GKF500 warranty Drive Belt Replacement, Friction Wheel Inspection

Page 18

6

Maintaining

Your Snow

Thrower

NEVER replace the auger shear pins with standard hex pins. Any damage to the auger gearbox or other components as a result of failing to do so will NOT be covered by your snow thrower’s warranty.

Drive Belt Replacement

To remove and replace your snow thrower’s auger belt,

 

 

proceed as follows:

c

b

1.

Remove the plastic belt cover on the front of the

 

 

 

 

engine by removing the two self-tapping screws. See

 

 

 

Figure 6-4.

 

 

2.

Drain the gasoline from the snow thrower, or place a

 

 

 

piece of plastic under the gas cap.

 

 

3.

Carefully pivot the snow thrower up and forward so

 

 

 

that it rests on the auger housing. See Figure 6-5.

a

 

4.

Remove the frame cover from the underside of the

 

 

 

 

snow thrower by removing four self-tapping screws

 

 

 

which secure it. See Figure 6-5.

 

 

5.

a. Use a wrench to pivot the idler pulley toward the

 

 

 

right. See Figure 6-9.

 

Figure 6-9

 

b. Roll the auger belt off the engine pulley.

 

c. Lift the drive belt off engine pulley.

6.Slip the drive belt off the pulley and between friction wheel and friction wheel disc. See Figure 6-10.

7 Remove and replace belt in the reverse order.

Friction Wheel Inspection

If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjust- ment fails to correct the problem, the friction wheel may need to be replaced.

NOTE: Special tools are required and several com-

 

ponents must be removed and in order to replace the

 

snow thrower’s friction wheel rubber. See an authorized

 

Service Dealer to have the friction wheel rubber

 

replaced or phone Customer Support as instructed on

 

page 2 for information on ordering a Service Manual.

Figure 6-10

 

To inspect the friction wheel, proceed as follows:

1.Place a piece of plastic under the gas cap and tighten securely.

2. Carefully pivot the snow thrower up and forward so that it rests on the auger housing. See Figure 6-5.

3. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. See Figure 6-5.

4. Examine the friction wheel for signs of wear or cracking. See Figure 6-11.

Figure 6-11

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OPERATOR’S Manual Two-Stage Snow ThrowerTable of Contents Finding and Recording Model NumberCustomer Support Chute Clean-out Tool Your Responsibility Restrict the usePreparation Safe Operation PracticesTraining Your ResponsibilityDo not modify engine Maintenance & StorageOperation Average Useful LifeSetting Up Setting Up Your Snow Thrower Shear Pin Storage optionalDrift Cutters If Equipped Snowthrower ModelAll models Skid Shoes Clean-Out ToolLamp Wiring Harness If equipped Tire Pressure Pneumatic TiresOperating Your Snow Thrower $26% #/.42 Gas & Oil Fill-Up Stopping The EngineElectric Starter If Equipped Recoil Starter To Engage DriveTo Engage Augers Auger Control TestChute Control Making AdjustmentsShift Cable Drive Control & Shift LeverStandard Skid Shoe Reversible Skid ShoeLubrication Maintaining Your Snow ThrowerEngine AugersAuger Belt Replacement Roll the auger belt off the engine pulley. See FigureUnhook the support bracket spring from the frame Drive Belt Replacement Friction Wheel InspectionRemove and replace belt in the reverse order Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 12.08.06OHV Part Description RÉF Pièce 30 in/po Remarque Lhabitacle peut être légèrement différent 5952Part Description RÉF Pièce 31AE6GKF500 Part Manual Chute Control Part Description RÉF Pièce Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Garantie FrottementSolution Causes Problème DépannagePropre et SouffleuseCarburant le Videz Gaz ’entretien RégimeFrottement de roue la de Inspection Transmission de courroie la de Remplacement Ne Remarque Les RemarqueTarière La de courroie la de RemplacementPatins et plate Lame LubrificationPatins Tarière la de CommandeRéglages Plastique en réversible Patins 4-5 FigureVitesses de levier Et transmission la de CommandeGoulotte la de Commande Vitesses de changement de CâbleToucher SouffleuseMain 150F dépasserModèles ’huile et d’essence PleinsModèles certains sur électrique Démarreur Certains sur électrique DémarreurSouffleuse la Trans de commande la de BlocageLa de proximité à 33/-3.42Souffleuse la de Commandes Départ de Volet’essence plein le jamais faites Ne Pneumatiques Bandages pneus des Pression Général d’ordre RecommandationsGoulotte la de dégagement de Outil Goulotte la de dégagement de OutilÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage Quant moteur du d’utilisation notice la consulter veuillez InférieurEmployer à moteur à l’huile à et carburant au ’assemblage Après .ESSENCE Sans mais d’huile pleinRemisage et Entretien Moyenne utile vie de DuréeGaz de émissions les concernant Avis Formation UtilisationPréparation Responsabilité VotreSécurité de Étiquettes De OutilMatières des Table Vente-après ServiceModèle de numéro le trouver Pour SouffleusePhases deux neige à Souffleuse Ca.troybilt.www

31AE6GKF500 specifications

The Troy-Bilt 31AE6GKF500 is a versatile and efficient tiller designed to meet the needs of both novice and experienced gardeners. As a robust piece of equipment, it combines powerful performance with user-friendly features, making it a popular choice for those looking to cultivate their gardens with ease.

One of the standout features of the Troy-Bilt 31AE6GKF500 is its powerful engine. Equipped with a reliable 4-cycle engine, this tiller delivers ample torque and efficient fuel consumption, ensuring that users can tackle tough soil conditions without compromising on performance. The tiller's self-propelled design further enhances its usability, allowing users to navigate effortlessly through their garden beds while maintaining optimal control.

The Troy-Bilt 31AE6GKF500 features a sturdy set of rotatable tines that can reach a depth of up to 6 inches, making it suitable for various soil types and gardening tasks. These tines can be easily adjusted for width, allowing gardeners to customize their tilling experience based on the size of their garden. With a tilling width of 16 inches, this tiller can cover substantial ground, saving time and effort while preparing soil for planting.

User comfort is prioritized in the design of the Troy-Bilt 31AE6GKF500. It boasts an ergonomically designed handle that can be easily adjusted to accommodate different user heights, reducing fatigue during extended use. Additionally, the adjustable handlebar can be folded down for convenient storage, making it an ideal choice for those with limited space.

Another noteworthy characteristic of this tiller is its durable construction. Built with high-quality materials, the Troy-Bilt 31AE6GKF500 promises longevity, ensuring that it can withstand the rigors of frequent gardening tasks. Its compact design enhances its maneuverability, making it easy to operate in tight corners and small spaces.

Safety features are integral to the design of the Troy-Bilt 31AE6GKF500. The tiller comes equipped with a safety switch that prevents accidental starts, giving users peace of mind during operation.

In conclusion, the Troy-Bilt 31AE6GKF500 is an efficient and reliable tiller that caters to the needs of gardeners looking for a powerful and user-friendly gardening tool. With its robust engine, adjustable tines, ergonomic design, and safety features, it stands out as a top choice for both amateur and seasoned gardeners alike.
Top Page Image Contents