Troy-Bilt 769-03800 warranty Maintaining Your Snow Thrower, Engine, Lubrication

Page 14

6

Maintaining

Your Snow

Thrower

WARNING

Before lubricating, repairing, or inspect- ing, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop.

Engine

Refer to the separate engine manual packed with your unit for all engine maintenance.

Lubrication

Engine

Refer to the separate engine manual packed with your unit for all engine lubrication instructions.

Gear Shaft

The gear (hex) shaft should be lubricated at least once a season or after every 25 hours of operation.

1.Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

2.Remove the lower frame cover by removing the two screws which secure it.

3.Apply a light coating of an all-weather multi-purpose oil to the hex shaft. See Figure 6-1.

NOTE: Avoid getting oil on rubber friction wheel and aluminum drive plate.

Wheels

At least once a season, remove both wheels. Clean and coat the axles with a multipurpose automotive grease before reinstalling wheels.

Chute Directional Control (optional)

Once a season, the joystick should be lubricated with petroleum jelly, linseed oil, mineral oil, paraffin wax or 3-in-1 oil.

Auger Shaft

At least once a season, remove the shear pins on auger shaft. Spray lubricant inside shaft, around the spacers. Also lubricate the flange bearings found at either end of the shaft. See Figure 6-2.

 

Figure 6-1

 

3HEARE0IN

3PACERS

"EARING

 

 

 

Figure 6-2

 

Keep all grease and oil off of the rubber friction wheel and aluminum drive plate.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary. To remove skid shoes:

1. Remove the four carriage bolts and hex flange nuts which secure them to the snow thrower.

2. Reassemble new skid shoes with the four carriage bolts (two on each side) and hex flange nuts. Refer to Figure 6-3.

To remove shave plate:

1. Remove the carriage bolts and hex nuts which attach

 

it and the skid shoes to the snow thrower housing.

Figure 6-3

 

2.Reassemble new shave plate, making sure heads of carriage bolts are to the inside of housing. Tighten securely.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Two-Stage Snow Thrower Box 1386, KITCHENER, Ontario N2G 4J1Customer Support Table of ContentsFinding and Recording Model Number Safety Labels Your Responsibility Restrict the usePreparation Safe Operation PracticesTraining Your ResponsibilityDo not modify engine Maintenance & StorageOperation Average Useful LifeSetting Up Your Snow Thrower Lamp Wiring Harness If equipped Clean-Out ToolHousing Ice from the chuteOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Electric Starter on certain models Gas & Oil Fill-UpStopping The Engine Recoil Starter To Engage DriveTo Engage Augers Auger Control TestShift Cable Making AdjustmentsChute Assembly optional Drive ControlProperty Chute Bracket AdjustmentTire Pressure Lubrication Maintaining Your Snow ThrowerEngine Shave Plate and Skid ShoesAuger Belt Replacement Unhook the support bracket spring from the frameDrive Belt Replacement Friction Wheel Removal Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty Four Year Supreme WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Manual Chute Control Part Description RÉF Pièce Optional/en option Part Description RÉF Pièce 30 in/po Part Description RÉF Pièce 31AE6GKF500 Part For parts and/or accessories refer to customer support on For parts and/or accessories refer to customer support on Page Garantie FrottementSolution Causes Problème DépannagePropre et Carburant le Videz Gaz’entretien Régime Tarières De courroie la de RemplacementTransmission ’entretien RégimeMoteur Patins et plate LameLubrification La de support du Ajustement RéglagesGoulotte PatinsVitesses de changement de Câble Transmission la de CommandeOption en Goulotte Avertissement Lanceur à DémarreurModèles ’huile et d’essence PleinsModèles certains sur électrique Démarreur Certains sur électrique DémarreurTrans de commande la de Blocage Gou la de direction de CommandeGoulotte la de Commande Tarière la de CommandeSouffleuse la de Commandes ’huile PleinDégagement Phare du câblage de FaisceauÉchéant cas le coupe de Barres De OutilSe pièces les toutes que ce jusqu’à Goulotte la de dégagement de OutilGoulotte la dégager De d’essayer avant immobilisées soient Guidon le derrière restez et moteur leMoyenne utile vie de Durée Remisage et EntretienResponsabilité Votre Gaz de émissions les concernant AvisFormation UtilisationPréparation Responsabilité VotreSécurité de Étiquettes Est goulotte la de dégagement de outil UnMatières des Table Vente-après ServiceModèle de numéro le trouver Pour Phases deux neige à Souffleuse Ca.troybilt.www

769-03800 specifications

The Troy-Bilt 769-03800 is a powerful and reliable rear-tine tiller designed to cater to both gardening enthusiasts and professional landscapers. Known for its durability and efficiency, this tiller boasts a robust design that makes it suitable for a variety of soil types, allowing users to prepare their garden beds with ease.

One of the standout features of the Troy-Bilt 769-03800 is its strong 14-inch steel tines, which are capable of slicing through hard-packed earth and clay with minimal effort. The tiller is equipped with a sizable 196cc engine that provides adequate power for tilling deeper and larger areas, ensuring that you can accomplish your gardening tasks quickly. The rear-tine configuration also means that the tiller can maneuver smoothly forward while the tines work through the soil, making the tilling process more efficient.

Another significant characteristic of this tiller is its adjustable tilling width. Users can choose between a range of widths from 16 inches to 24 inches, allowing for flexibility based on the specific needs of their garden or landscaping project. This feature enhances versatility, whether you are tackling narrow rows or wide garden plots.

The Troy-Bilt 769-03800 has a user-friendly control system, featuring an adjustable handlebar that accommodates various user heights and ensures comfort during operation. This ergonomic design reduces fatigue, making it easier to manage larger tilling projects.

In addition to its powerful performance, the tiller incorporates innovative technologies such as the patented "Bolo Tines," which are specially designed to break up soil more efficiently. This feature helps reduce the time and effort required for tilling, allowing users to achieve better results with less strain.

Safety is paramount with the Troy-Bilt 769-03800, as it includes features like a safety switch that ensures the engine can only be started when the user is ready. This prevents accidental starts and enhances overall user protection while operating the machine.

Overall, the Troy-Bilt 769-03800 is a versatile and robust tiller that combines power, efficiency, and user-friendly features. Whether you're a dedicated gardener or manage a larger landscape project, its reliable performance and innovative design make it a highly sought-after tool in the gardening community. For those looking to enhance their gardening experience, the Troy-Bilt 769-03800 is a worthwhile investment that promises to deliver exceptional results year after year.
Top Page Image Contents