Troy-Bilt 31AH9Q77766 Stopping the Engine, To Engage Drive, To Engage Augers, Operating Tips

Page 13

5.As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to the FULL position and then slowly into the OFF position again.

NOTE: Allow the engine to warm up for a few minutes after starting. The engine will not develop full power until it reaches operating temperatures.

Stopping the Engine

Run engine for a few minutes before stopping to help dry off any moisture on the engine.

1.Move throttle control to STOP position.

2.Remove the ignition key (do not turn key) to prevent unauthorized use of equipment.

3.Wipe all snow and moisture from the area around the engine as well as the area in and around the drive control and auger control. Also, engage and release both controls several times.

NOTE: Keep the key in a safe place. The engine cannot start without the ignition key.

To Engage Drive

1.With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.

NOTE: Use slower speeds in higher snow and/or until you are familiar with the snow thrower operation.

2.Squeeze drive control against the right handle and the snow thrower will move. Release it and the drive motion will stop.

IMPORTANT: NEVER move the shift lever without first releasing the wheel drive control. Doing so will cause premature wear on the drive system’s friction wheel.

3.To turn the unit left or right, squeeze the respective wheel steering control. See Figure 4-1.

To Engage Augers

1.To engage augers and start snow throwing, squeeze the left hand auger control against the left handle. Release to stop augers.

2.While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged.

NOTE: This same lever also locks auger control so you can turn the chute control without interrupting the snow throwing process.

3.Release the auger control; the interlock mechanism should keep the auger control engaged until the drive control is released.

4.Release the drive control to stop both the augers and the wheel drive. To stop the auger, both levers must be released.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of the muffler and the surrounding areas may exceed 150° F. Avoid these areas.

If possible, remove snow immediately after it falls.

Discharge snow downwind whenever possible.

Slightly overlap each previous path.

Set the skid shoes 1/4-inch below the shave plate for normal usage. Adjust them upward for hard-packed snow and downward when using on gravel or crushed rock.

Chute Clean-Out Tool

The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow and ice become lodged in the chute assembly during operation, proceed as follows to safely clean the chute assembly and chute opening:

1.Release both the Auger Control and the Drive Control.

2.Stop the engine by removing the ignition key.

3.Remove the clean-out tool from the clip which secures it to the rear of the auger housing. See Figure 4-1.

4.Use the shovel-shaped end of the clean-out tool to dislodge and scoop any snow and ice which has formed in and near the chute assembly.

5.Refasten the clean-out tool to the mounting clip on the rear of the auger housing, reinsert the ignition key, and start the snow thrower’s engine.

6.While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow and ice from the chute assembly.

4

Operating

Your Snow

Thrower

WARNING

The muffler, engine, and surrounding areas become hot and can cause a burn. Do not touch.

NOTE: Use slower speeds in higher snow and/or until you are familiar with the snow thrower operation.

IMPORTANT

NEVER move the shift lever without first releasing the wheel drive control. Doing so will cause premature wear on the drive system’s friction wheel.

13

Image 13
Contents Form no -00381C Two-Stage Snow Thrower Storm 31AH9Q7776628/06 Finding and Recording Model Number Table of ContentsCustomer Support 53% %842! #!54/ %. /0%2!4 Your Responsibility%, 352&!#%3  2%!$ /0%2!4/2g3 -!.5!,Your Responsibility Restrict the use TrainingPreparationOperation Maintenance & StorageDo not modify engine Your ResponsibilitySetting Up Your Snow Thrower Setting Up Your Snow Thrower Specifications are Auger Drive Subject to change Control Final AdjustmentsTesting Drive Control & Shift Lever Testing Auger Drive ControlAdjust the lock nut as follows Adjusting Drive and Auger ControlsTire Pressure Pneumatic Tires Reattach the spring to the actuator bracketKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Starting the Engine Gas & Oil Fill-UpElectric Starter Any conditionsStopping the Engine Chute Clean-Out ToolTo Engage Drive To Engage AugersShift Rod Making AdjustmentsChute Control Drive ControlSkid Shoes Chute Bracket AdjustmentAuger Control PlateEngine Maintaining Your Snow ThrowerLubrication AugersShave Plate Shave Plate Skid ShoesReplacing Belts Auger BeltAlways stop engine Performing any type Maintenance on Your machineDisconnect spark Plug, and ground Against engine beforeDrive Belt Hex Shaft Changing Friction WheelSecure with the cupped washer and hex bolt removed earlier Hub Assembly Friction WheelPreparing Engine Off-Season StoragePreparing Snow Thrower Short-Term StorageFor further details Contact an authorized Service center Problem Cause RemedyThis section addresses minor service issues Trouble- shootingStorm To order replacement Parts, call Or visit Parts List30 17 42 710-0458 Screw, Carr., 5/16-18 x Storm Sprocket, 32T 81 710-1245B Screw, Hx Cap 5/16-24 Page U.S.A Canada MANUFACTURER’S Limited Warranty for

31AH9Q77766 specifications

The Troy-Bilt 31AH9Q77766 is a robust and versatile riding lawn mower designed to meet the diverse needs of homeowners looking for efficient lawn care solutions. Known for its reliability and performance, this model blends advanced technology with user-friendly features, making it a popular choice for both novice and experienced gardeners.

One of the standout features of the Troy-Bilt 31AH9Q77766 is its powerful engine. Equipped with a reliable 382cc single-cylinder engine, it delivers robust performance to tackle various lawn terrains. This engine enhances the mower's cutting capabilities while ensuring fuel efficiency, making lawn maintenance both effective and economical.

The mower boasts a 30-inch cutting deck, which strikes the perfect balance between maneuverability and cutting width. This compact size allows it to navigate tight spaces, such as flower beds and fences, while still covering a substantial area in a single pass. The cutting deck is also equipped with a mulch kit that helps return nutrients back to the soil, promoting a healthier lawn.

User comfort and convenience are key aspects of the Troy-Bilt 31AH9Q77766. The operator's seat is designed for comfort, featuring a high-back design that provides ample support during long mowing sessions. Additionally, the mower is equipped with an easy-to-use dashboard that displays essential indicators, including fuel level and engine status, allowing users to monitor their mowing efficiently.

The Troy-Bilt 31AH9Q77766 also incorporates advanced technologies such as Troy-Bilt's proprietary IntelliPower system. This innovative feature automatically adjusts engine speed based on the cutting load to maintain optimal performance. As a result, users benefit from consistent cutting performance, even in thick grass.

Moreover, this riding mower comes with an automatic transmission that simplifies gear shifting, allowing users to focus on the task at hand instead of wrestling with complicated controls. The tight turning radius further enhances maneuverability, enabling users to make precise turns and navigate around obstacles seamlessly.

Maintenance is made easier with the Troy-Bilt 31AH9Q77766, thanks to its accessible design for routine oil changes and deck cleaning. The mower's build quality and durability ensure it withstands the rigors of regular use, making it a long-term investment for homeowners.

In conclusion, the Troy-Bilt 31AH9Q77766 stands out as a dependable riding mower equipped with a powerful engine, advanced technologies, and user-friendly features. Its combination of efficiency, comfort, and ease of maintenance makes it an ideal choice for homeowners looking to enhance their lawn care experience.