Troy-Bilt 31AH9Q77766 warranty Shave Plate Skid Shoes, Replacing Belts, Auger Belt

Page 17

Shave Plate and

Skid Shoes

The shave plate and skid shoes on the bottom of the

 

 

6

snow thrower are subject to wear. Check these periodi-

 

 

cally and replace as necessary.

 

 

Maintaining

Skid Shoes

 

 

NOTE: The skid shoes on this machine have two wear

 

 

Your Snow

edges. When one side wears out, they can be rotated

 

Skid Shoe

180° to use the other edge.

 

Thrower

 

 

1. Remove the six carriage bolts and lock nuts that

Shave Plate

 

secure the two skid shoes to the sides of the auger

 

 

 

housing. Refer to Figure 6-3.

 

 

 

2. Position the new skid shoes and secure with the

 

 

 

carriage bolts and nuts. Make certain the skid shoes

 

 

 

are adjusted to be level.

 

Figure 6-3

 

 

 

 

Shave Plate

1.Remove the nuts and carriage bolts that secure the shave plate to the bottom of the housing, Figure 6-3.

2.Remove the rear most hex nut and carriage bolt

securing the back of each skid shoe to the sides of the housing. Loosen the remaining hex nuts that secure the skid shoes.

3. Slide the shave plate out of the off-set slot at the bottom of the housing, and from between the skid shoes and side panels of the housing.

4. With the mounting holes toward the back, slide the new shave plate into position and secure with the fasteners removed previously.

Figure 6-4

Specifications are subject to change without notification or obligation. Images may not reflect your exact model and are for reference purposes only.

Replacing Belts

1.Disconnect the chute crank assembly at the discharge chute end by removing the hairpin clip and the flat washer. Refer to Figure 6-4.

2. Remove the plastic belt cover, located near the engine, by removing the three self-tapping screws that secure it. See Figure 6-5.

3. a. Loosen the bolt shown in Figure 6-6 securing the belt keeper bracket and remove the other bolt.

b. Push the belt keeper and bracket up off the engine pulley. See Figure 6-7.

Auger Belt

4. Remove the hairpin clip and flat washer from the ferrule in order to disconnect the auger idler rod from the brake bracket assembly. See Figure 6-8.

5. Unhook the spring found on the end of the auger cable from its respective actuator bracket. Refer to

Figure 3-10 in the “Setting Up Your Snow Thrower”Figure 6-5section.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 28/06 Two-Stage Snow Thrower Storm 31AH9Q77766Form no -00381C Customer Support Table of ContentsFinding and Recording Model Number 53% %842! #!54/ %. /0%2!4 Your Responsibility%, 352&!#%3  2%!$ /0%2!4/2g3 -!.5!,Your Responsibility Restrict the use TrainingPreparationOperation Maintenance & StorageDo not modify engine Your ResponsibilitySetting Up Your Snow Thrower Setting Up Your Snow Thrower Specifications are Auger Drive Subject to change Control Final AdjustmentsTesting Drive Control & Shift Lever Testing Auger Drive ControlAdjust the lock nut as follows Adjusting Drive and Auger ControlsTire Pressure Pneumatic Tires Reattach the spring to the actuator bracketKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Starting the Engine Gas & Oil Fill-UpElectric Starter Any conditionsStopping the Engine Chute Clean-Out ToolTo Engage Drive To Engage AugersShift Rod Making AdjustmentsChute Control Drive ControlSkid Shoes Chute Bracket AdjustmentAuger Control PlateEngine Maintaining Your Snow ThrowerLubrication AugersShave Plate Shave Plate Skid ShoesReplacing Belts Auger BeltAlways stop engine Performing any type Maintenance on Your machineDisconnect spark Plug, and ground Against engine beforeDrive Belt Hex Shaft Changing Friction WheelSecure with the cupped washer and hex bolt removed earlier Hub Assembly Friction WheelPreparing Engine Off-Season StoragePreparing Snow Thrower Short-Term StorageFor further details Contact an authorized Service center Problem Cause RemedyThis section addresses minor service issues Trouble- shootingStorm To order replacement Parts, call Or visit Parts List30 17 42 710-0458 Screw, Carr., 5/16-18 x Storm Sprocket, 32T 81 710-1245B Screw, Hx Cap 5/16-24 Page U.S.A Canada MANUFACTURER’S Limited Warranty for

31AH9Q77766 specifications

The Troy-Bilt 31AH9Q77766 is a robust and versatile riding lawn mower designed to meet the diverse needs of homeowners looking for efficient lawn care solutions. Known for its reliability and performance, this model blends advanced technology with user-friendly features, making it a popular choice for both novice and experienced gardeners.

One of the standout features of the Troy-Bilt 31AH9Q77766 is its powerful engine. Equipped with a reliable 382cc single-cylinder engine, it delivers robust performance to tackle various lawn terrains. This engine enhances the mower's cutting capabilities while ensuring fuel efficiency, making lawn maintenance both effective and economical.

The mower boasts a 30-inch cutting deck, which strikes the perfect balance between maneuverability and cutting width. This compact size allows it to navigate tight spaces, such as flower beds and fences, while still covering a substantial area in a single pass. The cutting deck is also equipped with a mulch kit that helps return nutrients back to the soil, promoting a healthier lawn.

User comfort and convenience are key aspects of the Troy-Bilt 31AH9Q77766. The operator's seat is designed for comfort, featuring a high-back design that provides ample support during long mowing sessions. Additionally, the mower is equipped with an easy-to-use dashboard that displays essential indicators, including fuel level and engine status, allowing users to monitor their mowing efficiently.

The Troy-Bilt 31AH9Q77766 also incorporates advanced technologies such as Troy-Bilt's proprietary IntelliPower system. This innovative feature automatically adjusts engine speed based on the cutting load to maintain optimal performance. As a result, users benefit from consistent cutting performance, even in thick grass.

Moreover, this riding mower comes with an automatic transmission that simplifies gear shifting, allowing users to focus on the task at hand instead of wrestling with complicated controls. The tight turning radius further enhances maneuverability, enabling users to make precise turns and navigate around obstacles seamlessly.

Maintenance is made easier with the Troy-Bilt 31AH9Q77766, thanks to its accessible design for routine oil changes and deck cleaning. The mower's build quality and durability ensure it withstands the rigors of regular use, making it a long-term investment for homeowners.

In conclusion, the Troy-Bilt 31AH9Q77766 stands out as a dependable riding mower equipped with a powerful engine, advanced technologies, and user-friendly features. Its combination of efficiency, comfort, and ease of maintenance makes it an ideal choice for homeowners looking to enhance their lawn care experience.
Top Page Image Contents