Troy-Bilt 31AH9Q77766 warranty $26% #/.42

Page 11

Auger Control

!5'%2

#/.42/,

'/

The auger control is located on the left handle. Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop.

Drive Control / Auger Lock

$2)6%

#/.42/,

'/

The drive control is located on the right handle. Squeeze the control grip against the handle to engage the wheel drive. Release to stop.

The drive control also locks the auger control so you can operate the chute directional control without interrupting the snow throwing process. If the auger control is en- gaged simultaneously with the drive control, the operator can release the auger control (on the left handle) and the augers will remain engaged. Release both controls to stop the augers and wheel drive.

IMPORTANT: Always release the drive control before changing speeds.

Chute Tilt Control

The distance snow is thrown can be changed by adjust- ing the angle of the chute assembly. Move the chute tilt control forward to decrease the distance, toward the rear to increase.

Chute Directional Control

The chute directional control is located on the left side of the snow thrower.

•To change the direction in which snow is thrown, crank clockwise to discharge to the left and counter- clockwise to discharge to the right.

Wheel Steering Controls

The left and right wheel steering controls are located on the underside of the handles. Squeeze the right control to turn right; squeeze the left control to turn left.

NOTE: Operate the snow thrower in open areas until you are familiar with these controls.

Ignition Key

The ignition key must be inserted and snapped in place in order for the engine to start. Remove the ignition key to prevent unauthorized use of equipment. Do NOT attempt to turn the key.

Clean-Out Tool

The clean-out tool is mounted to the rear of the auger housing and is designed to clear a clogged chute. Refer to Using Clean-Out Tool later in this section for instruc- tions on how to properly use it.

WARNING: Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.

NOTE: The clean-out tool is fastened to the rear of the auger housing with a cable tie. Cut the cable tie before operating the snow thrower.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces.

4

Operating

Your Snow

Thrower

WARNING

The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear safety glasses while operating the snow thrower, or while perform- ing any adjustments or repairs on it.

Be sure no one other than the operator is standing near the snow thrower while starting engine or operating snow thrower. Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and loose clothing away from any moving parts on engine and snow thrower.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 28/06 Two-Stage Snow Thrower Storm 31AH9Q77766Form no -00381C Customer Support Table of ContentsFinding and Recording Model Number  2%!$ /0%2!4/2g3 -!.5!, Your Responsibility53% %842! #!54/ %. /0%2!4 %, 352&!#%3Your Responsibility Restrict the use TrainingPreparationYour Responsibility Maintenance & StorageOperation Do not modify engineSetting Up Your Snow Thrower Setting Up Your Snow Thrower Testing Auger Drive Control Final AdjustmentsSpecifications are Auger Drive Subject to change Control Testing Drive Control & Shift LeverReattach the spring to the actuator bracket Adjusting Drive and Auger ControlsAdjust the lock nut as follows Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Any conditions Gas & Oil Fill-UpStarting the Engine Electric StarterTo Engage Augers Chute Clean-Out ToolStopping the Engine To Engage DriveDrive Control Making AdjustmentsShift Rod Chute ControlPlate Chute Bracket AdjustmentSkid Shoes Auger ControlAugers Maintaining Your Snow ThrowerEngine LubricationAuger Belt Shave Plate Skid ShoesShave Plate Replacing BeltsPlug, and ground Against engine before Performing any type Maintenance on Your machineAlways stop engine Disconnect sparkDrive Belt Hex Shaft Changing Friction WheelSecure with the cupped washer and hex bolt removed earlier Hub Assembly Friction WheelShort-Term Storage Off-Season StoragePreparing Engine Preparing Snow ThrowerTrouble- shooting Problem Cause RemedyFor further details Contact an authorized Service center This section addresses minor service issuesStorm To order replacement Parts, call Or visit Parts List30 17 42 710-0458 Screw, Carr., 5/16-18 x Storm Sprocket, 32T 81 710-1245B Screw, Hx Cap 5/16-24 Page U.S.A Canada MANUFACTURER’S Limited Warranty for

31AH9Q77766 specifications

The Troy-Bilt 31AH9Q77766 is a robust and versatile riding lawn mower designed to meet the diverse needs of homeowners looking for efficient lawn care solutions. Known for its reliability and performance, this model blends advanced technology with user-friendly features, making it a popular choice for both novice and experienced gardeners.

One of the standout features of the Troy-Bilt 31AH9Q77766 is its powerful engine. Equipped with a reliable 382cc single-cylinder engine, it delivers robust performance to tackle various lawn terrains. This engine enhances the mower's cutting capabilities while ensuring fuel efficiency, making lawn maintenance both effective and economical.

The mower boasts a 30-inch cutting deck, which strikes the perfect balance between maneuverability and cutting width. This compact size allows it to navigate tight spaces, such as flower beds and fences, while still covering a substantial area in a single pass. The cutting deck is also equipped with a mulch kit that helps return nutrients back to the soil, promoting a healthier lawn.

User comfort and convenience are key aspects of the Troy-Bilt 31AH9Q77766. The operator's seat is designed for comfort, featuring a high-back design that provides ample support during long mowing sessions. Additionally, the mower is equipped with an easy-to-use dashboard that displays essential indicators, including fuel level and engine status, allowing users to monitor their mowing efficiently.

The Troy-Bilt 31AH9Q77766 also incorporates advanced technologies such as Troy-Bilt's proprietary IntelliPower system. This innovative feature automatically adjusts engine speed based on the cutting load to maintain optimal performance. As a result, users benefit from consistent cutting performance, even in thick grass.

Moreover, this riding mower comes with an automatic transmission that simplifies gear shifting, allowing users to focus on the task at hand instead of wrestling with complicated controls. The tight turning radius further enhances maneuverability, enabling users to make precise turns and navigate around obstacles seamlessly.

Maintenance is made easier with the Troy-Bilt 31AH9Q77766, thanks to its accessible design for routine oil changes and deck cleaning. The mower's build quality and durability ensure it withstands the rigors of regular use, making it a long-term investment for homeowners.

In conclusion, the Troy-Bilt 31AH9Q77766 stands out as a dependable riding mower equipped with a powerful engine, advanced technologies, and user-friendly features. Its combination of efficiency, comfort, and ease of maintenance makes it an ideal choice for homeowners looking to enhance their lawn care experience.
Top Page Image Contents