Troy-Bilt 1028, 1130 manual Cable Tie

Page 21

Model 1028

	Ref.	Part No.	Part Description
	No.	Part No.	Part Description
	No.

	1.	714-0507	Cotter Pin
	2.	756-0178	Flat Idler
	3.	784-5632B	Auger Idler Arm
	4.	710-0347	Hex Cap Screw 3/8-16 x 1.75
	5.	738-0281	Shoulder Screw
	6.	736-0174	Wave Washer
	7.	732-0611	Extension Spring
	8.	712-3068	Hex Nut 5/16-18
	9.	710-0642	Self Tapping Screw, 1/4-20 x.75
	10.	711-04283	Auger Axle, 28”
	11.	05931A	Housing
	12.	741-0309	Ball Bearing
	13.	710-0451	Carriage Bolt, 5/16-18 x.75
	14.	705-5226	Chute Reinforcement
	15.	684-04132	Auger Housing Assembly, 28”
	16.	712-04063	Flange Lock Nut 5/16-18
	17.	714-0161	Hi-Pro Key, 3/16 x 5/8
	18.	715-04021	Dowel Pin
	19.	717-0528A	Worm Gear, 20-tooth
	20.	717-0526	Worm Shaft
	21.	731-2635	Clean-Out Tool Mount
	22.	731-2643	Clean-Out Tool
	23.	718-04071	Thrust Collar
	24.	790-00087	Bearing Housing
	25.	721-0325	Grease Plug
	26.	710-0726	Hex Screw 5/16-12

	Ref.	Part No.	Part Description
	No.


	27. 725-0157		Cable Tie

28.712-04065 Flange Lock Nut 3/8-16

29.	741-0245	Hex Flange Bearing
30.	790-00091	Skid Shoe
31.	721-0327	Grease Seal
32.	736-0351	Flat Washer,.76 x 1.5 x.030
33.	790-00118	Shave Plate, 28”
34.	710-0451	Carriage Bolt 5/16-18 x 1.00
35.	684-0065	Impeller Assembly
36.	715-0114	Pin

37.618-04206 Gear Assembly Complete, 28”

38.684-04108 Spiral Assembly - RH

39.	736-0188	Flat Washer
40.	741-0493A	Flange Bushing

41.684-04107 Spiral Assembly - LH

42.738-04124 Shear Pin,.25 x 1.50

43.731-04870 Spacer, 1.25OD x.75ID x 1.00 Lg.

44.	618-0123	RH Housing (Incl ref. 45 & 46)
45.	721-0179	Oil Seal
46.	741-0661A	Flange Bearing
47.	618-0124	LH Housing (Incl ref. 45 & 46)
48.	736-3084	Flat Washer,.51 x 1.12 x.06
49.	741-0662	Flange Bearing,.75 x 1.0 x.59
50.	741-0663	Flange Bearing,.503 ID x.75 OD
51.	737-3000	Lube Fitting, 3/16 Drive

21

Image 21

Contents Operator’s Manual Table of Contents Training Important Safe Operation PracticesMaintenance and Storage Assembling Your Snow Thrower Clean-Out Tool Know Your Snow ThrowerDrive Control / Auger Control Lock Safety Ignition Key Heated Handles Switch ModelAuger Drive Control Chute Tilt ControlOperating Your Snow Thrower To Engage Track Drive To Stop EngineTo Engage Augers Recoil StarterOperating Tips Drift Cutters If EquippedSnow Thrower Model Drift Cutter Kit All models OEM-390-679 150F. Avoid these areasChute Assembly Auger ControlDrive Control and Shift Lever Maintaining Your Snow Thrower Shift Rod AdjustmentSkid Shoes CarburetorGear Case Drive / Auger Control LockAuger Shaft Auger BearingsServicing Your Snow Thrower Belt Removal And ReplacementAugers Shave Plate and Skid ShoesDrive Belt Off-Season Storage EngineProblem Cause Remedy TroubleshootingParts List for Models 1028 Part Description Models 1028Model Cable Tie 31 23 51 -04871 Spacer, 1.25OD x.75ID x 3/16 Lg Supplied On engine Models 1028 22 20 238 Models 1028 Models 1028 Models 1028 Page MANUFACTURER’S Limited Commercial Warranty For MANUFACTURER’S Limited Warranty for