Troy-Bilt 1130, 1028 Know Your Snow Thrower, Clean-Out Tool, Drive Control / Auger Control Lock

Page 6

If not already attached, slip the cables that run from the handle panel to the chute assembly into the cable guide located on top of the engine. See Figure 3.

Cable

Cable

 

Guide

Discharge

 

Chute

 

Figure 3

If not already attached, unwrap the headlight wire which is attached to the headlight, beneath the handle panel. Wind the headlight wire around the lower right handle until excess slack is removed. See Figure 4.

Plug the wire from the headlight into the alternator lead coming from the right side of the engine underneath the fuel tank.

Alternator Lead

Alternator

Lead

Lamp Wire

NOTE: Wheels are omitted from illustration for clarity.

Figure 4

Clean-Out Tool

This tool, along with the electric cord, is fastened with a cable tie to the rear of the auger housing for shipping purposes. Cut the cable tie and remove the electric cord before operating the snow thrower.

SECTION 3: KNOW YOUR SNOW THROWER

Drive Control /

 

Shift Lever

 

 

Auger Control Lock

 

 

Chute Tilt

 

 

 

 

 

 

 

 

 

 

Control

Heated Handles

 

 

 

 

 

 

 

 

 

 

 

Heated Grip†

 

 

 

 

 

 

 

 

 

 

 

Switch†

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Headlight††

Auger Drive Control

 

Chute

Track Steering

Assembly

Control

 

Clean-Out

Primer

 

Tool

 

 

Choke

Chute Directional

ControlSafety

Ignition Key

 

Skid Shoe

 

Throttle

Auger

† Model 1028

Control

 

 

 

†† Model 1130 equipped with one (1)

Electric

Starter

Button

Switch

Box

Recoil

Starter

Handle

Closed

Open

Fuel Shut-Off Valve

*If Equipped

Figure 5

WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

Drive Control / Auger Control Lock

The drive control is located on the right handle. Squeeze the drive control to engage the wheel drive. Release to stop. See Figure 5.

6

Image 6
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingMaintenance and Storage Assembling Your Snow Thrower Clean-Out Tool Know Your Snow ThrowerDrive Control / Auger Control Lock Auger Drive Control Heated Handles Switch ModelSafety Ignition Key Chute Tilt ControlOperating Your Snow Thrower To Engage Augers To Stop EngineTo Engage Track Drive Recoil StarterSnow Thrower Model Drift Cutter Kit All models OEM-390-679 Drift Cutters If EquippedOperating Tips 150F. Avoid these areasChute Assembly Auger ControlDrive Control and Shift Lever Skid Shoes Shift Rod AdjustmentMaintaining Your Snow Thrower CarburetorAuger Shaft Drive / Auger Control LockGear Case Auger BearingsAugers Belt Removal And ReplacementServicing Your Snow Thrower Shave Plate and Skid ShoesDrive Belt Engine Off-Season StorageTroubleshooting Problem Cause RemedyParts List for Models 1028 Models 1028 Part DescriptionModel Cable Tie 31 23 51 -04871 Spacer, 1.25OD x.75ID x 3/16 Lg Supplied On engine Models 1028 22 20 238 Models 1028 Models 1028 Models 1028 Page MANUFACTURER’S Limited Commercial Warranty For MANUFACTURER’S Limited Warranty for