Snapper 155223 important safety instructions Maintenance and Storage

Page 23

IMPORTANT SAFETY INSTRUCTIONS

OPERATIONAL PRECAUTIONS

(Continued From Previous Page)

7.DO NOT put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

8.Start engine only where exhaust fumes will be safely dissipated. Allow a brief warm-up period, and practice operation of controls outside before putting the machine to work.

9.After striking a foreign object, STOP the engine (motor), remove the key, and remove the wire from spark plug. Thoroughly inspect the snow thrower for any damage, and repair the damage

before restarting and operating the snow thrower.

10.STOP the engine if the machine starts to vibrate

excessively as this normally indicates mechanical problems. Remove the key and disconnect the spark plug wire to prevent

unintentional starting before servicing or repairing the machine.

11.DO NOT clear snow across the face of slopes.

Exercise extreme CAUTION when changing direction on slopes. DO NOT attempt to clear steep slopes.

12.DO NOT leave machine unattended with the engine running. STOP engine and remove key to prevent unauthorized operation.

13.Release clutch control and make sure auger/impeller has STOPPED before adjusting deflector, or placing hands near auger/impeller.

14.DO NOT use snow thrower on surfaces above ground level, such as, a roof of a building.

15.Exercise extreme CAUTION when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

16.DO NOT overload the machine capacity by attempting to clear snow at too fast a rate.

17.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when backing.

18.Disengage power to the auger/impeller when snow thrower is transported or not in use.

19.Use only attachments and accessories approved by the manufacturer of the snow

thrower (such as wheels weights, counterweights, cabs and the like).

20.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles.

Walk; never run.

MAINTENANCE AND STORAGE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark, or pilot light as in a water heater, furnace, clothes dryer or other gas appliance. Allow

engine to cool before storing machine in an enclosure. Store fuel container out of reach of

children in a well ventilated, unoccupied building.

2.Keep machine and engine free of excess oil, grease and spilled fuel to reduce fire hazard.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Inspect all bolts, nuts and screws frequently and keep properly tightened.

5.Use only recommended shear bolts (if

equipped) to prevent possible damage to machine.

6.Service engine and make adjustments only when engine is stopped. Remove key, remove wire from spark plug, secure wire away from plug, and disconnect cord from electric starting motors to prevent accidental starting.

7.DO NOT change engine governor speed settings or overspeed engine.

8.DO NOT test for spark by grounding the spark plug next to spark plug hole. Spark from the plug could ignite gas exiting engine.

9.Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices.

10.Use only genuine SNAPPER replacement parts

to assure that original standards are maintained.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model Designation Series Designation Engine HP Auger Width TWO Stage Intermediate Frame Snow Thrower SeriesImportant Safety Instructions Maintenance and Storage Contents PRE-START Check List Operating InstructionsPropelling Snow Thrower STARTING, Operation StoppingRecoil Start Models EngineStopping ENGINE, Auger & Wheel Drive AdjustmentEngaging Auger Engaging Wheel DriveSTARTING, Operation & Stopping Electric Start Models Operating Instructions General Lubrication Service After First 5 Hours Check Auger Drive BeltIntroduction Check Wheel Drive BeltStorage Procedure MaintenanceAdjustment Auger Belt Idler Pulley Adjustment ADJUSTMENT/REPLACEMENTDo not Auger Belt ReplacementW2t¢,o,,,vo Skid Shoe Adjustment Ground Speed AdjustmentHP Models Only Single Handle Control AdjustmentRubber Drive Tire Replacement Chute Crank AdjustmentUSE HRS Season Service Performed EachDisclaimer of Warranty Year Limited WarrantyTWO Stage Intermediate Frame Snow Thrower Series TWO Stage Intermediate Frame Snow Thrower Series Important Safety Instructions Maintenance and Storage Contents T4Q STARTING, Operation Stopping Oo,o,o WI STARTING, Operation & Stopping Electric Start Models Operating Instructions Maintenance Maintenance III V12 W2t¢,o,,,vo Ground Speed Adjustment Blowerclutch Chute Crank Adjustment Troubleshooting Year Limited Warranty TWO Stage Intermediate Frame Snow Thrower Series

155223 specifications

The Snapper 155223 is a highly regarded machine in the realm of outdoor power equipment, particularly recognized for its robust performance and innovative features. Designed for homeowners seeking an efficient lawn mowing solution, the Snapper 155223 combines power, durability, and user-friendly functionality.

One of the standout features of the Snapper 155223 is its 22-inch steel mowing deck. This deck provides a wide cutting area, allowing users to cover larger sections of lawn in less time. The durable steel construction ensures longevity, resisting the wear and tear that often comes from regular use. Additionally, the mowing deck is designed for a clean and precise cut, promoting healthy grass growth.

The Snapper 155223 is powered by a reliable Briggs & Stratton engine, specifically engineered to deliver consistent power and performance. This 190cc engine not only offers ample horsepower but also integrates fuel-efficient technology, making it an economical choice for lawn care. The engine's easy-start feature simplifies the startup process, allowing users to get to work quickly.

Tech-savvy advancements are evident in the Snapper 155223 as well. It features a variable speed self-propelled drive system that allows users to adjust the pace of the mower according to their comfort and the terrain's conditions. This adaptability is particularly beneficial when maneuvering around obstacles or tackling uneven ground.

The Snapper 155223 also emphasizes user comfort and convenience. Its ergonomic handle design minimizes fatigue during extended use, while the adjustable cutting height provides flexibility for different grass types and seasonal growth conditions. Users can select from multiple height settings to achieve the perfect cut.

Furthermore, maintenance is made easy with the Snapper 155223. The mower includes a rear discharge option and is compatible with mulching capabilities, allowing users the flexibility to choose how they want to manage grass clippings. The integrated washout port simplifies cleaning the mowing deck, enhancing the overall maintenance experience.

In summary, the Snapper 155223 stands out as a versatile and durable lawn mower, packed with features that cater to the needs of the modern homeowner. Its powerful engine, robust cutting deck, and user-friendly technologies make it an excellent choice for anyone looking to maintain a beautiful lawn efficiently and effectively.
Top Page Image Contents