White Outdoor 9235 warranty Adjustments Maintenance

Page 10

6

Adjustments

&

Maintenance

WARNING

Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

NEVER attempt to make any adjustments while the engine

is running, except where specified in the operator’s manual.

Before servicing,

repairing, or inspecting, disengage the control bail and stop engine. Wait until all moving parts have come

to a complete stop.

Disconnect spark plug

wire and ground it

against the engine to prevent unintended starting.

Side View

Figure 6-1

Figure 6-2

WARNING: Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

WARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s manual.

Lubrication

Lubricate pivot points on the auger control and the extension spring at the end of the control cable with a light oil once every season and before storage of the snow thrower at the end of the season.

Adjusting Shave Plate

1.To check the adjustment of the shave plate, place the unit on a level surface. The wheels, shave plate and augers should all contact level surface. Note that if the shave plate is adjusted too high, snow may blow under the housing. If the shave plate wears out excessively, or the unit does not self-propel, the shave plate may be too low and needs to be adjusted.

NOTE: On new units or units with a new shave plate installed, the augers may be slightly off the ground.

2.To adjust, tip the snow thrower back so that it rests on the handle. Loosen the four lock nuts and bolts which secure the shave plate to the housing. See Figure 6-1. Move the shave plate to desired position and retighten the nuts and bolts securely.

Replacing Shave Plate

The shave plate is attached to the bottom of the auger housing and is subject to wear. It should be checked periodically. There are two wearing edges and the shave plate can be reversed. Refer to Figure 6-1.

1.Remove the four carriage bolts and hex lock nuts which attach it to the snow thrower housing.

2.Install new shave plate, making sure the heads of the carriage bolts are on the inside of the housing.

3.Adjust the shave plate according to instructions above. Tighten the nuts securely before operating the snow thrower.

Control Cable

As a result of both the control cable and the drive belt stretching due to wear, periodic adjustments may be necessary.

If the auger seems to hesitate when rotating while the engine maintains a constant speed, an adjustment is necessary. Proceed as follows:

The upper hole in the control handle provides for an adjustment in cable tension. To adjust, disconnect the end of control cable from the bottom hole in the control handle and reinsert it in the upper hole. Insert the cable from the outside as shown in Figure 6-2. Test the snow thrower to see if there is a noticeable difference.

Replacing Belt

WARNING: Before servicing, repairing, or inspecting, disengage the auger control and stop engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting.

10

Image 10
Contents Model 235, S235 Single-Stage Snow Thrower05/2006 Table of Contents Safety Labels Your ResponsibilityTrainingPreparation Safe OperationPractices This manual On the machineOperation Maintenance & StorageSafe Operation Practices Restrict the useSetup And Adjustment Know Your Snow ThrowerFuel And Oil Mixture OperationBefore Starting Fuel Fill-UpOperating the Snow Thrower Recoil StarterTo Stop Engine Clearing SnowAdjustments Maintenance Carburetor Replacing Auger PaddlesEngine Do not allow Auger’s rubber paddlesPreparing Snow Thrower Do not drain Carburetor if using Fuel stabilizerPreparing Engine Drain fuel into anPlease do not Return the unit to Trouble ShootingEngine runs erratic Log onto Or call a customerModel S235 Snow Thrower Part List3014 710-1882 736-0400 Flat Washer .194 x .62 x 750-0589Page Page MANUFACTURER’S Limited Warranty for