White Outdoor 31AH7Q3G190 manual To Engage Track Drive, To Engage Augers, Operating Tips

Page 10

Electric Starter:

•Connect power cord to switch box on engine, then to 120 volt AC receptacle. With the engine running, push starter button and spin the starter for several seconds. The unusual sound made by spinning the starter will not harm engine or starter. Disconnect the power cord from receptacle first, and then from switch box.

Recoil Starter

•With engine running, pull starter rope with a rapid, continuous full arm stroke three or four times. Pulling the starter rope will produce a loud clattering sound, which is not harmful to the engine or starter.

•Move throttle control to “stop” or “off” position.

•Remove ignition key. Do not turn key. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended.

NOTE: Keep it in a safe place. Engine will not start without ignition key.

Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times.

To Engage Track Drive

•With the engine running near top speed, move the shift lever into one of the six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.

NOTE: Use slower speeds in higher snow and until you are familiar with the operation of the snow thrower.

•Squeeze the traction control against the right handle and the snow thrower will move. Release it and the drive motion will stop.

IMPORTANT: NEVER move the shift lever without first releasing the traction control. Doing so will cause premature wear to the drive system’s friction wheel.

To Engage Augers

To engage the augers and start the snow throwing action, proceed as follows:

•Squeeze the auger control against the left handle. To disengage power to the augers:

•Release both the auger control and the traction control, if engaged.

The auger control can be locked so you can turn the electric chute directional control without interrupting the snow throwing process.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of the muffler and the surrounding areas may

exceed 150°F. Avoid these areas.

•For the most efficient snow removal, remove snow immediately after it falls.

•Discharge the snow downwind whenever possible.

•Slightly overlap each previous path.

•Set the skid shoes 1/4" below the shave plate for normal usage. The skid shoes may be adjusted upward (to lower the shave plate) for hard-packed snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock.

•Be certain to follow the precautions found in the To Stop Engine section to prevent possible freeze-up.

•Clean the snow thrower thoroughly after each use.

SECTION 5: MAKING ADJUSTMENT

WARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s manual.

Skid Shoe Adjustment

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes. Refer to Skid Shoe Adjustment in the Assembly Section.

Auger Control Adjustment

Refer to the information found under Final Adjustments in the Assembly Section to adjust the auger control.

Chute Assembly Adjustment

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to the Chute Tilt Control in the Know Your Snow Thrower Section.

Traction Control Adjustment

Refer to the information found under Final Adjustment in the Assembly Section to adjust the traction control. If you are uncertain that you have reached the correct adjustment, proceed as follows:

WARNING: Drain the gasoline out of the snow thrower’s tank, or place a piece of plastic film under the gas cap to avoid spillage BEFORE making the adjustment.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OPERATOR’S Manual Table of Contents Preparation Important Safe Operation PracticesTraining OperationMaintenance And Storage Unpacking AssemblyAssembling Your Snow Thrower Loose PartsSkid Shoe Adjustment Final AdjustmentsAuger Control Adjustment Traction Control and Shift Lever AdjustmentAuger Drive Control Know Your Snow ThrowerChute Tilt Control Skid ShoeHeated Handles Switch Electric Chute-Rotation SwitchSafety Ignition Key Track Steering ControlsOperating Your Snow Thrower Chute Assembly Adjustment Skid Shoe AdjustmentAuger Control Adjustment Traction Control AdjustmentMaintaining Your Snow Thrower Shift Rod AdjustmentLubrication Engine Servicing Your Snow ThrowerAugers Auger Belts Belt Removal And ReplacementShave Plate and Skid Shoes Drive BeltServicing Friction Wheel Rubber Off-season StoragePage Troubleshooting Problem Cause RemedyModel 31AH7Q3G190 Part DescriptionFor Reference Only 17 -0620A Shift Rod Upper 18 -0621 Shift Rod Lower 749-0951 2321 Oyster Gray Powder Black Red Metallic Model 31AH7Q3G190 Models 31AH7Q3G190 22 20 Model 31AH7Q3G190 Models 31AH7Q3G190 Models 31AH7Q3G190 MANUFACTURER’S Limited Warranty for

31AH7Q3G190 specifications

The White Outdoor 31AH7Q3G190 is a versatile and robust snow blower designed to tackle the toughest winter conditions. Built to cater to homeowners looking for an efficient solution to their snow removal needs, this model combines power, durability, and user-friendly features.

One of the standout features of the 31AH7Q3G190 is its 24-inch clearing width, allowing users to clear a wide path quickly and effectively. This wide auger ensures that even heavier snow accumulations can be handled with ease, making it ideal for areas with significant snowfall. The snow blower boasts a powerful 208cc engine, providing the necessary torque and reliability needed to handle various snow conditions, from light flurries to heavy, wet snow.

The snow blower is equipped with a 6-speed transmission, offering operators the flexibility to adjust their speed as needed. This feature allows for efficient maneuvering, whether on flat driveways or sloped surfaces. Additionally, the unit features an adjustable chute that can rotate 180 degrees, giving users precise control over snow direction. This is particularly valuable when clearing driveways or sidewalks, enabling users to avoid unwanted snow piles.

For enhanced usability, the 31AH7Q3G190 is designed with electric start technology, ensuring that starting the machine is hassle-free. This is a particularly attractive feature for those who may struggle with traditional pull-start mechanisms in cold weather. The snow blower’s heavy-duty construction also includes reinforced handles that provide comfort and stability during operation, while the large, rugged tires offer superior traction, allowing users to traverse snowy terrains without slipping.

Safety is also a priority with this snow blower. It includes features such as an operator presence control, which ensures that the machine only operates when the user is in control. This minimizes the risk of accidents during operation, adding an extra layer of security.

In summary, the White Outdoor 31AH7Q3G190 snow blower combines power, efficiency, and user-centered design. Its durable build, powerful engine, and functional features make it an excellent choice for homeowners needing a reliable snow removal solution. Whether dealing with light dustings or heavy snowfalls, this snow blower delivers performance and convenience, ensuring that winter weather doesn't become a burden. Its combination of innovation and practicality stands as a testament to quality engineering, making it a valuable addition to any winter toolkit.
Top Page Image Contents