White Outdoor 31AH7Q3G190 manual Maintaining Your Snow Thrower, Shift Rod Adjustment, Lubrication

Page 11

Tip the snow thrower forward, allowing it to rest on the auger housing.

Remove the frame cover underneath the snow thrower by removing the six self-tapping screws.

With the traction control released, there must be clearance between the friction wheel and the drive plate in all positions of the shift lever.

With the traction control engaged, the friction wheel must contact the drive plate. See Figure 9.

Gear Shaft

Drive

Cable

Friction Wheel

Pivot Rod

 

Rubber

 

 

Drive

 

Plate

Figure 9

If adjustment is necessary:

Loosen the jam nut on the traction drive cable. Adjust the cable as necessary. Refer to Figure 5.

Retighten the jam nut to secure the cable when correct adjustment is reached.

Reassemble the frame cover.

NOTE: If you placed plastic film under the gas cap, be certain to remove it before operating the snow thrower.

Shift Rod Adjustment

To adjust the shift rod, proceed as follows:

Remove the hairpin clip and slide the shift rod connector up, to separate the upper shift rod from the lower shift rod. See Figure 10.

Place the shift lever into the sixth (6) position.

Rotate the shift arm clockwise (from the operator’s position) as far as it will go.

Thread the upper shift rod downward until the elbow on its lower end aligns with the hole found in the lower shift rod.

Reconnect the upper shift rod to the lower shift rod by reinserting the hairpin clip removed earlier and sliding the shift rod connector back down into place.

IMPORTANT: Make certain to check for correct adjustment of the shift rod as instructed under Final Adjustments in the Assembly Section, before operating the snow thrower.

 

Shift Lever

Hairpin Clip

 

Flat

 

Washer

Ferrule

 

 

Upper Shift Rod

Shift Rod

 

Connector

Hairpin Clip

 

Lower Shift Rod

Shift Arm

 

Figure 10

SECTION 6: MAINTAINING YOUR SNOW THROWER

WARNING: Before lubricating, repairing, or inspecting, disengage all clutch levers and stop engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting.

Lubrication

Engine

Refer to the separate engine manual packed with your unit for all engine lubrication instructions.

IMPORTANT: When following instructions in separate

engine manual for draining oil, be sure to protect frame to avoid oil dripping onto transmission parts.

Gear Shaft

Lubricate the gear shaft with 6-n-1 grease at least once a season or after every 25 hours of operation (available at automotive stores, or order part number 737-0170).

Refer to Figure 9.

IMPORTANT: Keep all grease and oil off of the rubber friction wheel and aluminum drive plate.

Drive and Shifting Mechanism

Lubricate at least once a season or after every 25 hours of operation. Remove the rear cover, lubricate any chains, sprockets, gears, bearings, shafts, and shifting

11

Image 11
Contents OPERATOR’S Manual Table of Contents Operation Important Safe Operation PracticesTraining PreparationMaintenance And Storage Loose Parts AssemblyAssembling Your Snow Thrower UnpackingTraction Control and Shift Lever Adjustment Final AdjustmentsAuger Control Adjustment Skid Shoe AdjustmentSkid Shoe Know Your Snow ThrowerChute Tilt Control Auger Drive ControlTrack Steering Controls Electric Chute-Rotation SwitchSafety Ignition Key Heated Handles SwitchOperating Your Snow Thrower Traction Control Adjustment Skid Shoe AdjustmentAuger Control Adjustment Chute Assembly AdjustmentLubrication Shift Rod AdjustmentMaintaining Your Snow Thrower Augers Servicing Your Snow ThrowerEngine Drive Belt Belt Removal And ReplacementShave Plate and Skid Shoes Auger BeltsOff-season Storage Servicing Friction Wheel RubberPage Problem Cause Remedy TroubleshootingPart Description Model 31AH7Q3G190For Reference Only 17 -0620A Shift Rod Upper 18 -0621 Shift Rod Lower 749-0951 2321 Oyster Gray Powder Black Red Metallic Model 31AH7Q3G190 Models 31AH7Q3G190 22 20 Model 31AH7Q3G190 Models 31AH7Q3G190 Models 31AH7Q3G190 MANUFACTURER’S Limited Warranty for

31AH7Q3G190 specifications

The White Outdoor 31AH7Q3G190 is a versatile and robust snow blower designed to tackle the toughest winter conditions. Built to cater to homeowners looking for an efficient solution to their snow removal needs, this model combines power, durability, and user-friendly features.

One of the standout features of the 31AH7Q3G190 is its 24-inch clearing width, allowing users to clear a wide path quickly and effectively. This wide auger ensures that even heavier snow accumulations can be handled with ease, making it ideal for areas with significant snowfall. The snow blower boasts a powerful 208cc engine, providing the necessary torque and reliability needed to handle various snow conditions, from light flurries to heavy, wet snow.

The snow blower is equipped with a 6-speed transmission, offering operators the flexibility to adjust their speed as needed. This feature allows for efficient maneuvering, whether on flat driveways or sloped surfaces. Additionally, the unit features an adjustable chute that can rotate 180 degrees, giving users precise control over snow direction. This is particularly valuable when clearing driveways or sidewalks, enabling users to avoid unwanted snow piles.

For enhanced usability, the 31AH7Q3G190 is designed with electric start technology, ensuring that starting the machine is hassle-free. This is a particularly attractive feature for those who may struggle with traditional pull-start mechanisms in cold weather. The snow blower’s heavy-duty construction also includes reinforced handles that provide comfort and stability during operation, while the large, rugged tires offer superior traction, allowing users to traverse snowy terrains without slipping.

Safety is also a priority with this snow blower. It includes features such as an operator presence control, which ensures that the machine only operates when the user is in control. This minimizes the risk of accidents during operation, adding an extra layer of security.

In summary, the White Outdoor 31AH7Q3G190 snow blower combines power, efficiency, and user-centered design. Its durable build, powerful engine, and functional features make it an excellent choice for homeowners needing a reliable snow removal solution. Whether dealing with light dustings or heavy snowfalls, this snow blower delivers performance and convenience, ensuring that winter weather doesn't become a burden. Its combination of innovation and practicality stands as a testament to quality engineering, making it a valuable addition to any winter toolkit.