Woods Equipment SB54S, SB84S, SB74S, SB64S Assembly Instructions, Dealer SET-UP Instructions

Page 21

ASSEMBLY INSTRUCTIONS

DEALER SET-UP INSTRUCTIONS

Assembly of this snowblower is the responsibility of the Woods dealer. It should be delivered to the owner com- pletely assembled, lubricated and adjusted for normal conditions.

The snowblower is shipped partially assembled. Assembly will be easier if components are aligned and loosely assembled before tightening hardware. Rec- ommended torque values for hardware are located on page 38.

Select a suitable working area. A smooth hard surface, such as concrete, will make assembly much quicker. Open parts boxes and lay out parts and hardware to make location easy. Refer to illustrations, accompany- ing text, parts lists and exploded view drawings.

All Models

1.Remove parts from crate in a suitable work area. Check packing list to ensure all parts are present.

NOTE: Leave all hardware loose until all compo- nents are completely assembled.

2.Remove driveshaft from snowblower. Slide imple- ment PTO shaft on gearbox shaft. Pull back spring actuated collar as driveline is installed on gearbox shaft, releasing collar when driveline is installed.

NOTE: Check that drive shaft is fully engaged in gearbox shaft groove.

3.Remove hardware (37) and (38) from front right mast plate hole and rotate drive holder (16) until holes are aligned, Figure 16.

4.Reinstall hardware (37) and (38).

16. Drive Holder

37.5/16 NC x 1" Carriage Bolt

38.5/16 NC Lock Nut

Figure 16. Install Drive Holder

5.Remove plug from gearbox and add .52 quart of SAE85W-90 gear oil, Figure 12.

6.Remove hardware (37) and (38) from SMV bracket

(34)and rotate bracket facing up. Reinstall hard- ware (37) and (38), Figure 17.

34. SMV Bracket

37.5/16 NC x 1" Carriage Bolt

38.5/16 NC Hex Locknut

Figure 17. SMV Installation

7.Remove plastic cable tie holding auger chain in place.

Install Hand Crank (Figure 18)

8.Fasten mount bracket (5) to upper three-point channel using two carriage bolts (8) and lock nuts

(9).

NOTE: Bracket is adjustable and can be rotated or slide up or down for best fit with tractor.

9.Connect clevis rotator (1) to block (2) and clevis tube (3) with roll pins (6).

10.Remove rotator sprocket from lower hitch pin. Install in square opening on chute adapter with block and pin assembly using roll pins (6) and (13). Hole in sprocket rotator should face towards tractor hitch.

11.Install trim strip (6.5" long) in slot on mount bracket

(5)which hand crank (4) will protrude through.

12.Slide hand crank (4) through mount bracket (5) and into clevis tube (3). Align hand crank and cle- vis tube holes for correct length and install cap screws (7) and hex nut (9).

(Rev. 10/4/2011)

MAN0869 (04/13/2011)

Assembly 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Snowblower To the Dealer IntroductionTable of Contents General Information SpecificationsSafety Rules SafetyTraining PreparationMaintenance Storage Safety & Instructional Decals Be Careful Operation OperationPrincipal Components Driveline Attachment Tractor RequirementsShortening Driveline Machine BREAK-INAfter operating for 1/2 hour Shear Bolts Operating Requirements After operating for 5 to 10 hoursTransporting Adjusting Discharge Chute PositionPRE-OPERATION Check List Owners Responsibility CleaningOwner Service Owner ServiceService and Maintenance Intervals Lubrication InformationChain Maintenance Driveline Shear Bolt ReplacementDischarge Chute Lubrication GearboxSkid Shoes PTO Driveline Guard Walterscheid DrivelineComer Driveline Problem Problem Causes Suggested Solution Trouble ShootingAssembly Instructions AssemblyInstall Hand Crank Figure Dealer SET-UP InstructionsInstall Discharge Chute Install Discharge Chute FigureMounting Hydraulic Chute ROTA- TOR Option Figure Hydraulic Chute Rotator InstallationInstall Wiring Harness Mouinting Hydraulic Chute DEFLEC- TOR FigureMounting Electric Chute Rotator Option Figure Mounting Electric Chute Deflec TOR Figure Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts SnowblowerSB54S, SB64S Subcompact Snowblower Assembly Part QTY Description SB54S, SB64S Subcompact Snowblower Parts ListSB74C, SB84C Compact Snowblower Assembly Hand Crank Assembly SB74C, SB84C Compact Snowblower Parts ListGearbox Assembly SB54S, SB64S Comer Shear Bolt Drive Assembly OptionalSB74C, SB84C SB54S, SB64S, SB74C, SB84C Walterscheid Drive Assembly OptionalHydraulic Chute Deflector Optional Hydraulic Chute Rotator OptionalElectric Chute Deflector Optional Electric Chute Rotator OptionalSAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartWarranty Rev /3/2011 Woods Equipment Company MAN0826

SB84S, SB54S, SB74S, SB64S specifications

Woods Equipment Company has established itself as a leader in the manufacturing of high-quality landscape equipment, and the SB series of landscape rakes—specifically the SB64S, SB74S, SB54S, and SB84S—stand out for their exceptional performance and innovative features.

The SB series is designed to meet the needs of both residential and commercial users. These models range in width from 54 inches to 84 inches, allowing for versatility in handling various tasks, whether you're maintaining a small garden or clearing a large lot. The difference in size also caters to different tractor sizes and horsepower ratings, making it easier for users to select a rake that fits their specific requirements.

A notable feature of the SB series is its durable construction. Built from high-strength steel, these rakes can withstand rigorous use in various environments. The rakes are further equipped with heavy-duty tines that are engineered to be resilient against breakage while providing optimal soil leveling and debris clearing performance.

The SB rakes utilize a patented Quick-Tatch mounting system. This system allows for fast and easy attachment and detachment from tractors, reducing downtime and enhancing productivity. Additionally, the rakes can be adjusted to various angles, enabling users to efficiently handle different tasks such as grading, levelling, or scarifying soil.

One of the key characteristics of the SB64S, SB74S, SB54S, and SB84S models is their ergonomic design. The rakes are built with user-friendly controls that facilitate operation. Operators can change the angle and height with ease, which contributes to overall efficiency while reducing the physical strain typically associated with manual adjustments.

The rakes also feature a heavy-duty frame that supports consistent performance across various job conditions, whether working on flat ground or uneven terrains. Enhanced stability during operation means users can trust that the rake will provide uniform results without compromising the integrity of the landscape.

Another technological advantage of the SB series is its versatility in compatible attachment options, which allows users to employ the rake for various applications beyond standard landscaping, including gravel leveling and road maintenance.

In conclusion, the Woods Equipment SB64S, SB74S, SB54S, and SB84S rakes offer a combination of strength, technology, and user convenience, making them essential tools for landscape management. Their wide range of sizes and features ensures that there is a suitable option for every need, allowing for efficient and effective work across diverse environments.
Top Page Image Contents