Yard-Man OGST-2806 manual Shift Rod, Auger Control, Wheel Drive Control, Chute Assembly

Page 12

SECTION 5: MAKING ADJUSTMENTS

WARNING: NEVER attempt to clean chute or make any adjustments while engine is running.

Shift Rod

•Remove the hairpin clip and flat washer from the shift handle under the handle panel. See Figure 13.

•Place shift lever in sixth (6) position or fastest forward speed.

•Push shift arm assembly down as far as it will go.

•Rotate the ferrule up or down on the shift rod as necessary until the ferrule lines up with the upper hole in the shift lever. See Figure 13.

•Insert ferrule from the left side of the snow thrower into the upper hole.

•Reinstall the hairpin clip and the washer.

IMPORTANT: Before operating the snow thrower, make

•Tip the snow thrower forward, allowing it to rest on the auger housing.

•Remove the frame cover underneath the snow thrower by removing six self-tapping screws.

•With the wheel drive control released, check if there is clearance between friction wheel and drive plate in all positions of the shift lever. See Figure 14.

•With the traction control lever engaged, check if the friction wheel solidly contacts the drive plate. See Figure 14. If not, adjust as follows:

•Loosen the jam nut on the traction drive cable and thread the cable in or out as necessary.

•Retighten the jam nut to secure the cable when correct adjustment is reached.

•Reassemble the frame cover.

•If you placed plastic film under the gas cap earlier, remove it now..

Shift Arm

Trigger Cables

 

sure the shift rod is adjusted according to instructions on page 7.

NOTE: For adjustment of auger control, skid shoe and chute assembly, refer to Final Adjustments in Section 2.

Auger Actuator Bracket

Hex Nut &

Drive Actuator Bracket

.

Shift Lever

Hairpin Clip

Flat Washer

Upper Shift Rod

Ferrule

Lower Shift Rod

Shift Arm

Clutch Rod

Connector

Cupped

Hex Gear

Shaft

Washer

 

Rubber

 

Friction

 

Wheel

 

Drive Plate

Figure 14

Auger Control

Refer to instructions on page 7 to adjust the auger control. Make certain to check for correct adjustment as instructed before operating the snow thrower.

Figure 13

Wheel Drive Control

If you are uncertain about correct adjustment, proceed as follows:

•Drain the gasoline out of your snow thrower’s engine, and place a piece of plastic film under the gas cap to avoid spillage.

Chute Assembly

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to page 9for instructions.

The remote chute control cables have been pre- adjusted at the factory. Move the remote chute lever on the control panel back and forward to adjust angle of the chute assembly.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingMaintenance And Storage Your ResponsibilityItems Required For Assembly Before Assembly Assembling HandleAssembling Your Snow Thrower Loose PartsAttaching the Chute Assembly Attaching Chute CrankChute Clean-Out Tool Final AdjustmentsWheel Drive Control & Shift Lever Auger ControlKnowing Your Snow Thrower Tire Pressure Pneumatic TiresDrive Control / Auger Control Lock Safety Ignition Key Chute Clean-Out ToolShift Lever Discharge ChuteOperating Your Snow Thrower Before StartingGas & Oil Fill-Up To Start EngineTo Engage Wheel Drive To Engage AugersOperating Tips Chute Assembly Shift RodAuger Control Wheel Drive ControlMaintaining Your Snow Thrower Skid ShoeGeneral Recommendations LubricationFriction Wheel Rubber Drive BeltsEngine Wheel Drive Control / Auger Control LockServicing Your Snow Thrower AugersShave Plate and Skid Shoes Replacing BeltsDrive Belt Changing Friction Wheel Rubber Sprocket Hex ShaftTroubleshooting OFF-SEASON StorageTWO Year Supreme Warranty 103 Part RÉF Pièce Description Complètement une moitié avec de la graisse no 838-0168 Part RÉF Pièce Description RÉF Pièce Description 20 19 3468 58A 58B Part RÉF Pièce Description 995 x 12,0 Lg po Couple de 325-550 po-lb Style Panneau-jaune nn Frottement de roues l’embrayage de pièces les et pneus Dépannage DE Guide 9 Chapitre Silicone de Ou légère d’huile couche d’une câbles, et roulements’arbre sur pignon le glissant en frottement de roue la Vers pignon du .hex moyeu le Tournez .hex l’arbre surFrottement de roue Caoutchouc en bague la de ChangementCourroies les de Remplacement Entretien 7 Chapitre Patins et LameTarières MoteurGénéral d’ordre Recommandations LubrificationTarière la de Commande Patin’éjection Goulotte Roues des l’entraînement de Commande La de commande la de réglage tout pour réglages»Goulotte la de et patins des tarière ’utilisation Conseils Tarières les de Embrayage’huile et d’essence Pleins Démarrage le AvantCarburateur «Montage» chapitreVitesses de Levier ’autre de Que plus côté d’un tirer de risque machine la pneus, lesTous dans égale pas n’est pression la Si Remarque Le dans roues» des l’entraînement de «Commande Réglages DerniersGoulotte la de dégagement de Outil La à «Réglages» chapitreGoulotte la de manivelle la de Montage Goulotte la de MontageSuivantes instructions Les utilisez assemblée, être doit elle Si .assembléeMontage 2 Chapitre Cisaillement de BoulonsResponsabilité Votre Remisage ET Entretien Préparation FormationVENTE-APRÈS Service ’utilisation Notice

OGST-2806 specifications

The Yard-Man OGST-2806 is a robust and versatile outdoor power equipment designed for serious gardeners and landscapers. This multi-functional tool is primarily recognized for its efficiency and ease of use, making it an essential addition to any outdoor toolkit.

At the core of the OGST-2806 is its powerful engine, which delivers impressive performance for tackling a variety of lawn care tasks. The engine is designed to offer high torque, ensuring that it can handle tough terrains and thick vegetation. This allows users to confidently complete tasks such as mowing, edging, and trimming without the fear of bogging down.

One of the standout features of the Yard-Man OGST-2806 is its lightweight construction, which facilitates easy maneuverability. This significantly reduces operator fatigue, enabling users to work for extended periods without discomfort. The compact design makes it easy to transport and store, which is a crucial factor for those with limited garage space.

The OGST-2806 is equipped with advanced features that enhance its functionality. It includes an adjustable handle, allowing users to customize the height for maximum comfort. Coupled with its ergonomic design, this ensures a comfortable grip and optimal control during operation. Additionally, the model incorporates a user-friendly start mechanism, reducing the hassle often associated with outdoor equipment.

Technologically, the Yard-Man OGST-2806 integrates innovative solutions for efficient operation. It utilizes a low-emission engine that not only meets environmental regulations but also provides quiet operation, making it perfect for residential areas. This is complemented by its fuel efficiency, allowing extended run times between refueling, which saves both time and money for users.

The Yard-Man OGST-2806 is also designed with safety in mind. It features a quick-stop blade brake, which halts blade rotation instantly when the operator releases the handle. This critical safety feature helps prevent accidents and provides peace of mind while working.

In conclusion, the Yard-Man OGST-2806 is a reliable, feature-rich outdoor power tool that blends power, efficiency, and safety. Its lightweight design, advanced engine technology, and user-friendly operation make it ideal for tackling a wide range of gardening tasks. For anyone looking to enhance their lawn care experience, the OGST-2806 stands out as a solid option.
Top Page Image Contents