Yard-Man OGST-2806 Maintaining Your Snow Thrower, Skid Shoe, General Recommendations, Lubrication

Page 13

Skid Shoe

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes.

For close snow removal, as when using on a smooth concrete or asphalt driveway, place the skid shoes in the low position. Use the middle or high position when the area to be cleared is uneven. When operating on gravel, always put skid shoes in the high position. See Figure 15.

Adjust skid shoes as follows:

•Loosen, but do not remove, the hex flange locknuts which fasten the skid shoe to the auger housing.

•Raise or lower the skid shoe to desired position.

•Retighten the hex nuts loosened earlier.

NOTE: Make certain the bottom surface of skid shoe is flat against the ground to avoid uneven wear .

Shave Plate

Skid

Shoes

High

Low

Hex Flange Locknuts

•Repeat on the other side of the snow thrower.

Figure 15

SECTION 6: MAINTAINING YOUR SNOW THROWER

WARNING: Before lubricating, repairing, or inspecting, disengage all clutch levers and stop engine. Wait until all moving parts have come to a complete stop. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

Gear Shaft

•Lubricate the gear shaft with 6-in-1 grease (part number 737-0170) at least once a season, or after every 25 hours of operation. Refer to Figure 14.

IMPORTANT: Keep all grease and oil off the rubber friction wheel and drive plate.

General Recommendations

•Always observe safety rules when performing any maintenance.

•The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain the snow thrower as instructed in this manual.

•Some adjustments will have to be made periodically to maintain your unit properly.

•Periodically check all fasteners and hardware to make sure these are tight.

Engine

Refer to the engine manual for instructions.

Gear Case

The gear case is lubricated with grease at the factory and it does not require checking.

•If disassembled for any reason, lubricate with 2 ounces of Shell Alvania grease EPR00, part number 737-0168. Before reassembling, remove old sealant and apply new sealant.

IMPORTANT: Do not overfill the gear case, since damage to the seals could result. Be sure the vent plug is free of grease in order to relieve pressure.

Lubrication

Drive and Shifting Mechanism

•At least once a season or after every 25 hours of operation, remove rear cover. Lubricate any chains, sprockets, gears, bearings, shafts, and the shifting mechanism at least once a season. Use engine oil or a spray lubricant. Refer to Figure 14.

IMPORTANT: Avoid spillage of oil on rubber friction wheel and aluminum drive plate.

Auger Shaft

•At least once a season, remove the shear pins from the auger shaft and spray lubricant inside the shaft. See Figure 16.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operator’s Manual Table of Contents Training Important Safe Operation PracticesYour Responsibility Maintenance And StorageBefore Assembly Assembling Handle Items Required For AssemblyAssembling Your Snow Thrower Loose PartsAttaching Chute Crank Attaching the Chute AssemblyFinal Adjustments Chute Clean-Out ToolWheel Drive Control & Shift Lever Auger ControlTire Pressure Pneumatic Tires Knowing Your Snow ThrowerDrive Control / Auger Control Lock Chute Clean-Out Tool Safety Ignition KeyShift Lever Discharge ChuteBefore Starting Operating Your Snow ThrowerGas & Oil Fill-Up To Start EngineTo Engage Augers To Engage Wheel DriveOperating Tips Shift Rod Chute AssemblyAuger Control Wheel Drive ControlSkid Shoe Maintaining Your Snow ThrowerGeneral Recommendations LubricationDrive Belts Friction Wheel RubberEngine Wheel Drive Control / Auger Control LockAugers Servicing Your Snow ThrowerShave Plate and Skid Shoes Replacing BeltsDrive Belt Sprocket Hex Shaft Changing Friction Wheel RubberOFF-SEASON Storage TroubleshootingTWO Year Supreme Warranty 103 Part RÉF Pièce Description Complètement une moitié avec de la graisse no 838-0168 Part RÉF Pièce Description RÉF Pièce Description 20 19 3468 58A 58B Part RÉF Pièce Description 995 x 12,0 Lg po Couple de 325-550 po-lb Style Panneau-jaune nn Frottement de roues l’embrayage de pièces les et pneus Dépannage DE Guide 9 Chapitre Ou légère d’huile couche d’une câbles, et roulements Silicone de’arbre sur pignon le glissant en frottement de roue la Vers pignon du .hex moyeu le Tournez .hex l’arbre surCaoutchouc en bague la de Changement Frottement de roueCourroies les de Remplacement Patins et Lame Entretien 7 ChapitreTarières MoteurLubrification Général d’ordre RecommandationsPatin Tarière la de Commande’éjection Goulotte La de commande la de réglage tout pour réglages» Roues des l’entraînement de CommandeGoulotte la de et patins des tarière Tarières les de Embrayage ’utilisation ConseilsDémarrage le Avant ’huile et d’essence PleinsCarburateur «Montage» chapitreVitesses de Levier Que plus côté d’un tirer de risque machine la pneus, les ’autre deTous dans égale pas n’est pression la Si Remarque Réglages Derniers Le dans roues» des l’entraînement de «CommandeGoulotte la de dégagement de Outil La à «Réglages» chapitreGoulotte la de Montage Goulotte la de manivelle la de MontageSuivantes instructions Les utilisez assemblée, être doit elle Si .assembléeCisaillement de Boulons Montage 2 ChapitreResponsabilité Votre Remisage ET Entretien Formation PréparationVENTE-APRÈS Service ’utilisation Notice

OGST-2806 specifications

The Yard-Man OGST-2806 is a robust and versatile outdoor power equipment designed for serious gardeners and landscapers. This multi-functional tool is primarily recognized for its efficiency and ease of use, making it an essential addition to any outdoor toolkit.

At the core of the OGST-2806 is its powerful engine, which delivers impressive performance for tackling a variety of lawn care tasks. The engine is designed to offer high torque, ensuring that it can handle tough terrains and thick vegetation. This allows users to confidently complete tasks such as mowing, edging, and trimming without the fear of bogging down.

One of the standout features of the Yard-Man OGST-2806 is its lightweight construction, which facilitates easy maneuverability. This significantly reduces operator fatigue, enabling users to work for extended periods without discomfort. The compact design makes it easy to transport and store, which is a crucial factor for those with limited garage space.

The OGST-2806 is equipped with advanced features that enhance its functionality. It includes an adjustable handle, allowing users to customize the height for maximum comfort. Coupled with its ergonomic design, this ensures a comfortable grip and optimal control during operation. Additionally, the model incorporates a user-friendly start mechanism, reducing the hassle often associated with outdoor equipment.

Technologically, the Yard-Man OGST-2806 integrates innovative solutions for efficient operation. It utilizes a low-emission engine that not only meets environmental regulations but also provides quiet operation, making it perfect for residential areas. This is complemented by its fuel efficiency, allowing extended run times between refueling, which saves both time and money for users.

The Yard-Man OGST-2806 is also designed with safety in mind. It features a quick-stop blade brake, which halts blade rotation instantly when the operator releases the handle. This critical safety feature helps prevent accidents and provides peace of mind while working.

In conclusion, the Yard-Man OGST-2806 is a reliable, feature-rich outdoor power tool that blends power, efficiency, and safety. Its lightweight design, advanced engine technology, and user-friendly operation make it ideal for tackling a wide range of gardening tasks. For anyone looking to enhance their lawn care experience, the OGST-2806 stands out as a solid option.
Top Page Image Contents