Yard-Man OGST-2806 manual Friction Wheel Rubber, Drive Belts, Engine, Auger Bearings and Shaft

Page 14

Shear Pin

Vent Plug

Cotter Pin

Wheel Drive Control / Auger Control Lock

The cams on the ends of the control rods which interlock the wheel drive and auger drive controls must be lubricated at least once a season or every 25 hours of operation using a multi-purpose automotive grease. The cams can be accessed beneath the handle panel. See Figure 18.

Figure 16

Discharge Chute

The base of the discharge chute and the spirals on the chute crank should be lubricated at least every 25 hours of use. Apply the lubricant under the base of the chute and where the spirals contact the discharge chute. See Figure 17.

Control Rods

Handle Panel

Lube Cams Here

Lube Under Chute Base

Chute Crank Spirals

 

Figure 17

Auger Bearings and Shaft

•Every season lubricate the auger bearings and the bearings on the side of the frame with light oil. See to Figure 16.

•Use oil or spray lubricant into the bearings at the wheels at least once a season. Remove the wheels, one side at a time, and clean and coat axles with multi-purpose automotive grease.

•Lubricate the auger shaft at least once a season. To do this:

•Remove the shear pins on the auger shaft.

•Oil or spray lubricant inside shaft.

•Carefully spin the auger around by hand to disperse the lubricant.

•Reinstall the shear pins.

Figure 18

Friction Wheel Rubber

Follow the instructions below to check the condition of the friction wheel rubber every 25 hours of operation.

•Remove the six self-tapping screws from the frame cover underneath the snow thrower.

•Visually inspect the friction wheel rubber for excessive wear, cracks, or loose fit on the friction wheel drive hub.

•Also engage the traction control and check if the friction wheel is making contact with friction plate. Refer to Figure 14. If it does not make contact, adjust the traction drive cable and recheck the friction wheel.

•Replace friction wheel rubber if necessary. Refer to instructions on page 17.

Drive Belts

Follow the instructions below to check the condition of the drive belts every 50 hours of operation.

•Remove the plastic belt cover on the front of the engine by removing the three self-tapping screws.

•Visually inspect for frayed, cracked, or excessively worn out belts.

•Replace belts as necessary as outlined in Service Section on page 15.

Engine

Follow accompanying engine manual for all engine- related maintenance issues.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingMaintenance And Storage Your ResponsibilityAssembling Your Snow Thrower Items Required For AssemblyBefore Assembly Assembling Handle Loose PartsAttaching the Chute Assembly Attaching Chute CrankWheel Drive Control & Shift Lever Chute Clean-Out ToolFinal Adjustments Auger ControlDrive Control / Auger Control Lock Knowing Your Snow ThrowerTire Pressure Pneumatic Tires Shift Lever Safety Ignition KeyChute Clean-Out Tool Discharge ChuteGas & Oil Fill-Up Operating Your Snow ThrowerBefore Starting To Start EngineOperating Tips To Engage Wheel DriveTo Engage Augers Auger Control Chute AssemblyShift Rod Wheel Drive ControlGeneral Recommendations Maintaining Your Snow ThrowerSkid Shoe LubricationEngine Friction Wheel RubberDrive Belts Wheel Drive Control / Auger Control LockShave Plate and Skid Shoes Servicing Your Snow ThrowerAugers Replacing BeltsDrive Belt Changing Friction Wheel Rubber Sprocket Hex ShaftTroubleshooting OFF-SEASON StorageTWO Year Supreme Warranty 103 Part RÉF Pièce Description Complètement une moitié avec de la graisse no 838-0168 Part RÉF Pièce Description RÉF Pièce Description 20 19 3468 58A 58B Part RÉF Pièce Description 995 x 12,0 Lg po Couple de 325-550 po-lb Style Panneau-jaune nn Frottement de roues l’embrayage de pièces les et pneus Dépannage DE Guide 9 Chapitre ’arbre sur pignon le glissant en frottement de roue la Silicone deOu légère d’huile couche d’une câbles, et roulements Vers pignon du .hex moyeu le Tournez .hex l’arbre surFrottement de roue Caoutchouc en bague la de ChangementCourroies les de Remplacement Tarières Entretien 7 ChapitrePatins et Lame MoteurGénéral d’ordre Recommandations Lubrification’éjection Goulotte Tarière la de CommandePatin Goulotte la de et patins des tarière Roues des l’entraînement de CommandeLa de commande la de réglage tout pour réglages» ’utilisation Conseils Tarières les de EmbrayageCarburateur ’huile et d’essence PleinsDémarrage le Avant «Montage» chapitreVitesses de Levier Tous dans égale pas n’est pression la Si Remarque ’autre deQue plus côté d’un tirer de risque machine la pneus, les Goulotte la de dégagement de Outil Le dans roues» des l’entraînement de «CommandeRéglages Derniers La à «Réglages» chapitreSuivantes instructions Goulotte la de manivelle la de MontageGoulotte la de Montage Les utilisez assemblée, être doit elle Si .assembléeMontage 2 Chapitre Cisaillement de BoulonsResponsabilité Votre Remisage ET Entretien Préparation FormationVENTE-APRÈS Service ’utilisation Notice

OGST-2806 specifications

The Yard-Man OGST-2806 is a robust and versatile outdoor power equipment designed for serious gardeners and landscapers. This multi-functional tool is primarily recognized for its efficiency and ease of use, making it an essential addition to any outdoor toolkit.

At the core of the OGST-2806 is its powerful engine, which delivers impressive performance for tackling a variety of lawn care tasks. The engine is designed to offer high torque, ensuring that it can handle tough terrains and thick vegetation. This allows users to confidently complete tasks such as mowing, edging, and trimming without the fear of bogging down.

One of the standout features of the Yard-Man OGST-2806 is its lightweight construction, which facilitates easy maneuverability. This significantly reduces operator fatigue, enabling users to work for extended periods without discomfort. The compact design makes it easy to transport and store, which is a crucial factor for those with limited garage space.

The OGST-2806 is equipped with advanced features that enhance its functionality. It includes an adjustable handle, allowing users to customize the height for maximum comfort. Coupled with its ergonomic design, this ensures a comfortable grip and optimal control during operation. Additionally, the model incorporates a user-friendly start mechanism, reducing the hassle often associated with outdoor equipment.

Technologically, the Yard-Man OGST-2806 integrates innovative solutions for efficient operation. It utilizes a low-emission engine that not only meets environmental regulations but also provides quiet operation, making it perfect for residential areas. This is complemented by its fuel efficiency, allowing extended run times between refueling, which saves both time and money for users.

The Yard-Man OGST-2806 is also designed with safety in mind. It features a quick-stop blade brake, which halts blade rotation instantly when the operator releases the handle. This critical safety feature helps prevent accidents and provides peace of mind while working.

In conclusion, the Yard-Man OGST-2806 is a reliable, feature-rich outdoor power tool that blends power, efficiency, and safety. Its lightweight design, advanced engine technology, and user-friendly operation make it ideal for tackling a wide range of gardening tasks. For anyone looking to enhance their lawn care experience, the OGST-2806 stands out as a solid option.
Top Page Image Contents