Yard-Man OGST-2806 manual Attaching the Chute Assembly, Attaching Chute Crank

Page 6

Attaching the Chute Assembly

NOTE: Your chute assembly may or may not be assembled. If it requires assembly use the following instructions.

Chute Assembly

Hex Screw

Hex Lock Nut

Chute Flange

Keeper

Figure 3

•Place chute assembly over chute opening, with the opening in the chute assembly facing the front of the unit. Place chute flange keepers beneath lip of chute assembly, with the flat side of chute flange keeper facing downward.

•Insert hex cap screws up through chute flange keeper and chute assembly as shown in Figure 3. Secure with hex flange locknuts. Tighten with two 7/16” wrenches. Do not over tighten.

Attaching Chute Crank

•Remove the hairpin clip from the upper chute crank and slide the upper chute crank through the upper chute crank bracket and into the lower chute crank. A pair of pliers may help in this job.

Upper Chute Crank

Upper Chute

Crank Bracket

Hairpin Clip

Lower Chute Crank

Figure 4

•Align the two holes on both chute cranks and secure with the hairpin clip removed earlier. See Figure 4.

•With the hex nuts loosened on the lower chute crank bracket (see Figure 5) adjust the bracket so that the spiral on the chute crank fully engages the teeth on the chute assembly. Tighten the nuts on the lower chute crank bracket securely.

Chute Directional

Control

Chute

Assembly

Lower Chute

Bracklet

Lock Nuts

Figure 5

•The cable ties normally are loosely installed on each side of the lower handle at the factory. Pull the cable ties tight to secure. Trim excess from the ends of cable ties.

•If not already attached, slip the cables that run from the handle panel to the discharge chute into the cable guide located on top of the engine.

See Figure 6.

Cables Cable

Guide

Discharge

Chute

Figure 6

•Wrap the wire from the head lamp down the right handle until the wire can be plugged into the alternator lead wire under the fuel tank.

Alternator Lead

Alternator

Lead

Lamp Wire

NOTE: Wheels are omitted from illustration for clarity.

Figure 7

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingMaintenance And Storage Your ResponsibilityAssembling Your Snow Thrower Items Required For AssemblyBefore Assembly Assembling Handle Loose PartsAttaching the Chute Assembly Attaching Chute CrankWheel Drive Control & Shift Lever Chute Clean-Out ToolFinal Adjustments Auger ControlKnowing Your Snow Thrower Tire Pressure Pneumatic TiresDrive Control / Auger Control Lock Shift Lever Safety Ignition KeyChute Clean-Out Tool Discharge ChuteGas & Oil Fill-Up Operating Your Snow ThrowerBefore Starting To Start EngineTo Engage Wheel Drive To Engage AugersOperating Tips Auger Control Chute AssemblyShift Rod Wheel Drive ControlGeneral Recommendations Maintaining Your Snow ThrowerSkid Shoe LubricationEngine Friction Wheel RubberDrive Belts Wheel Drive Control / Auger Control LockShave Plate and Skid Shoes Servicing Your Snow ThrowerAugers Replacing BeltsDrive Belt Changing Friction Wheel Rubber Sprocket Hex ShaftTroubleshooting OFF-SEASON StorageTWO Year Supreme Warranty 103 Part RÉF Pièce Description Complètement une moitié avec de la graisse no 838-0168 Part RÉF Pièce Description RÉF Pièce Description 20 19 3468 58A 58B Part RÉF Pièce Description 995 x 12,0 Lg po Couple de 325-550 po-lb Style Panneau-jaune nn Frottement de roues l’embrayage de pièces les et pneus Dépannage DE Guide 9 Chapitre ’arbre sur pignon le glissant en frottement de roue la Silicone deOu légère d’huile couche d’une câbles, et roulements Vers pignon du .hex moyeu le Tournez .hex l’arbre surFrottement de roue Caoutchouc en bague la de ChangementCourroies les de Remplacement Tarières Entretien 7 ChapitrePatins et Lame MoteurGénéral d’ordre Recommandations LubrificationTarière la de Commande Patin’éjection Goulotte Roues des l’entraînement de Commande La de commande la de réglage tout pour réglages»Goulotte la de et patins des tarière ’utilisation Conseils Tarières les de EmbrayageCarburateur ’huile et d’essence PleinsDémarrage le Avant «Montage» chapitreVitesses de Levier ’autre de Que plus côté d’un tirer de risque machine la pneus, lesTous dans égale pas n’est pression la Si Remarque Goulotte la de dégagement de Outil Le dans roues» des l’entraînement de «CommandeRéglages Derniers La à «Réglages» chapitreSuivantes instructions Goulotte la de manivelle la de MontageGoulotte la de Montage Les utilisez assemblée, être doit elle Si .assembléeMontage 2 Chapitre Cisaillement de BoulonsResponsabilité Votre Remisage ET Entretien Préparation FormationVENTE-APRÈS Service ’utilisation Notice

OGST-2806 specifications

The Yard-Man OGST-2806 is a robust and versatile outdoor power equipment designed for serious gardeners and landscapers. This multi-functional tool is primarily recognized for its efficiency and ease of use, making it an essential addition to any outdoor toolkit.

At the core of the OGST-2806 is its powerful engine, which delivers impressive performance for tackling a variety of lawn care tasks. The engine is designed to offer high torque, ensuring that it can handle tough terrains and thick vegetation. This allows users to confidently complete tasks such as mowing, edging, and trimming without the fear of bogging down.

One of the standout features of the Yard-Man OGST-2806 is its lightweight construction, which facilitates easy maneuverability. This significantly reduces operator fatigue, enabling users to work for extended periods without discomfort. The compact design makes it easy to transport and store, which is a crucial factor for those with limited garage space.

The OGST-2806 is equipped with advanced features that enhance its functionality. It includes an adjustable handle, allowing users to customize the height for maximum comfort. Coupled with its ergonomic design, this ensures a comfortable grip and optimal control during operation. Additionally, the model incorporates a user-friendly start mechanism, reducing the hassle often associated with outdoor equipment.

Technologically, the Yard-Man OGST-2806 integrates innovative solutions for efficient operation. It utilizes a low-emission engine that not only meets environmental regulations but also provides quiet operation, making it perfect for residential areas. This is complemented by its fuel efficiency, allowing extended run times between refueling, which saves both time and money for users.

The Yard-Man OGST-2806 is also designed with safety in mind. It features a quick-stop blade brake, which halts blade rotation instantly when the operator releases the handle. This critical safety feature helps prevent accidents and provides peace of mind while working.

In conclusion, the Yard-Man OGST-2806 is a reliable, feature-rich outdoor power tool that blends power, efficiency, and safety. Its lightweight design, advanced engine technology, and user-friendly operation make it ideal for tackling a wide range of gardening tasks. For anyone looking to enhance their lawn care experience, the OGST-2806 stands out as a solid option.
Top Page Image Contents