Cub Cadet 730 STE manual Drift Cutters, Operating Tips

Page 10

IMPORTANT: If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control.

•To readjust the control cable, loosen the hex jam nut on the auger control cable “Z” fitting.

•Rotate the coupling end of the cable counterclockwise to provide more slack.

•Retighten the hex jam nut. See Figure 7.

•Repeat Auger Control Test to verify proper adjustment has been achieved.

Auger

Control

Z-End

Jam Nut

Auger

Control Cable

Figure 7

Clean-Out Tool

The clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow and ice lodge itself in the chute assembly during operation, proceed as follows to safely clean the chute and chute opening:

•Release both the Auger Control and the Drive/ Auger Control Lock.

•Stop the engine by moving the throttle to the stop position.

•Remove the clean-out tool from the mounting clip.

•Use the shovel-shaped end of the clean-out tool to dislodge and scoop any snow and ice which has formed in and near the chute assembly.

WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing. Use the clean-out tool or a stick to unclog.

•Refasten the clean-out tool to the mounting clip on the rear of the auger housing, reinsert the ignition key and start the snow thrower’s engine.

•While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow and ice from the chute assembly.

Drift Cutters

Drift cutters should be used when operating the snow thrower in heavy drift conditions.

On models so equipped, drift cutters are assembled to the auger housing inverted. Remove the carriage bolts by unthreading the hex nuts which secure them, and reinstall the drift cutters in their proper position before operating the snow thrower. See Figure 8.

If your unit is not equipped with drift cutters, contact Customer Support as instructed on page 2 for information regarding price and availability.

Snow Thrower ModelDrift Cutter Kit

All models

OEM-390-679

Drift

 

Cutter

 

Carriage Screws

 

& Hex Nuts

 

Figure 8

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of the muffler and the surrounding areas may exceed 150°F. Avoid these areas.

•For the most efficient snow removal, remove snow immediately after it falls.

•Discharge the snow downwind whenever possible.

•Slightly overlap each previous path.

•Set the skid shoes 1/4" below the shave plate for normal usage. The skid shoes may be adjusted upward (to lower the shave plate) for hard-packed snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock.

•Be certain to follow the precautions found in the To Stop Engine section to prevent possible freeze-up.

•Clean the snow thrower thoroughly after each use.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Table of Contents Preparation Important Safe Operation PracticesTraining OperationYour Responsibility Maintenance & StorageDo not modify engine Assembling Your Snow Thrower Know Your Snow Thrower Clean-Out ToolDrive Control / Auger Control Lock Chute Tilt Control Safety Ignition KeyAuger Drive Control Skid ShoeBefore Starting Operating Your Snow ThrowerTrack Lock Lever Gas And Oil Fill-upTo Engage Augers To Stop EngineTo Engage Track Drive Recoil StarterDrift Cutters Operating TipsAuger Control Chute AssemblyDrive Control and Shift Lever Skid Shoes Shift Rod AdjustmentMaintaining Your Snow Thrower CarburetorAuger Shaft Drive / Auger Control LockGear Case Auger BearingsAugers Belt Removal And ReplacementServicing Your Snow Thrower Shave Plate and Skid ShoesReplacing Friction Wheel Rubber Drive BeltEngine Off-Season StorageTroubleshooting Problem Cause RemedyParts List for Model 730 STE Model 730 STE 2227 26 -0604A Hex Screw, 5/16-18 725-0157 Model 730 STE Model 730 STE Model 730 STE Track Steering Drive Shaft Model 730 STE MANUFACTURER’S Limited Commercial Warranty For MANUFACTURER’S Limited Warranty for

730 STE specifications

The Cub Cadet 730 STE is a powerful and versatile snow blower designed to tackle even the toughest winter conditions. Featuring a robust 24-inch clearing width, this snow thrower is engineered to handle heavy snowfall with ease. Its impressive throwing distance, which can reach up to 40 feet, makes it an ideal choice for both residential and commercial use. The 730 STE is equipped with a strong 277cc engine that provides reliable performance and the necessary power to push through packed snow and ice.

One of the standout features of the Cub Cadet 730 STE is its innovative track drive system. This advanced system ensures superior traction and stability on various surfaces, including steep inclines and uneven terrain. The track drive design gives users added confidence, allowing them to navigate snowy pathways and driveways without slipping or losing control.

The snow blower also incorporates a user-friendly control panel, allowing operators to easily manage speed settings and directional control. With multiple speed settings, the 730 STE enables users to adjust the pace for optimal efficiency based on the depth and type of snow being cleared. The highly maneuverable design of the snow blower makes it easy to work around obstacles such as mailboxes, fences, and landscaping.

Another remarkable feature of the Cub Cadet 730 STE is its adjustable chute. The 180-degree rotating chute allows users to direct the snow wherever they wish, ensuring efficient removal without worrying about blowing snow back onto already cleared areas. The chute is made from durable materials, enhancing its lifespan while maintaining effective performance.

Safety is also a priority in the design of the 730 STE. The snow blower comes with features such as a headlight for improved visibility during early morning or late evening snow clearing, making it safer to operate under low light conditions. Additionally, the durable and reinforced construction guarantees longevity and reliability throughout many winter seasons.

In summary, the Cub Cadet 730 STE stands out in the snow blower market with its powerful engine, superior traction, adjustable chute, and user-friendly controls. These characteristics make it an exceptional choice for anyone looking to tackle winter weather efficiently and effectively. Whether you're clearing your driveway or maintaining a commercial lot, the 730 STE is equipped to handle the task with performance and precision.
Top Page Image Contents