Cub Cadet 730 STE manual Chute Assembly, Auger Control, Drive Control and Shift Lever

Page 11

SECTION 4: MAKING ADJUSTMENTS

WARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s manual.

Chute Assembly

The distance snow is thrown can be adjusted by changing the angle of the upper chute. Move the chute tilt control forward to decrease the distance, toward the rear to increase.

Auger Control

Refer to Auger Control Test in the Operating Section to adjust the auger control.

Drive Control and Shift Lever

To check the adjustment of the drive control and shift lever, proceed as follows:

•To check the adjustment of the traction control clutch and shift lever, proceed as follows:

•With the engine off, move the shift lever all the way forward to the highest speed. With the drive control lever released, push the snow thrower forward. The unit should roll forward. Then engage the drive control. The wheels should stop turning.

•Now release the drive control and push the unit again.

•Move the shift lever back to the fast reverse position then all the way forward again. There should be no resistance in the shift lever, and the wheels should keep turning.

•If you have resistance when moving the shift lever or the wheels stop when they should not, loosen the jam nut on the drive control cable and unthread the cable one turn.

•If the wheels do not stop when you engage the drive control, loosen the jam nut on the drive control cable and thread the cable in one turn.

•Recheck the adjustment and repeat as necessary. Tighten the jam nut to secure the cable when correct adjustment is reached.

WARNING: Drain the gasoline out of the snow thrower’s tank, or place a piece of plastic film under the gas cap to avoid spillage BEFORE making the adjustment.

To test further for correct adjustment, if necessary, proceed as follows:

•Tip the snow thrower forward, allowing it to rest on the auger housing. See Figure 9.

Frame Cover

Auger

Housing

Figure 9

•Remove the frame cover underneath the snow thrower by removing the six self-tapping screws.

•With the drive control released, there must be clearance between the friction wheel and the drive plate in all positions of the shift lever.

•With the drive control engaged, the friction wheel must contact the drive plate. See Figure 10.

If adjustment is necessary:

•Loosen the jam nut on the drive cable. Adjust the cable as necessary.

•Retighten the jam nut to secure the cable when correct adjustment is reached.

•Reassemble the frame cover.

Gear Shaft

Drive

Cable

Friction Wheel

Pivot Rod

 

Rubber

 

 

Drive

 

Plate

Figure 10

NOTE: If you placed plastic film under the gas cap, be certain to remove it before operating the snow thrower.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operator’s Manual Table of Contents Operation Important Safe Operation PracticesTraining PreparationDo not modify engine Maintenance & StorageYour Responsibility Assembling Your Snow Thrower Drive Control / Auger Control Lock Clean-Out ToolKnow Your Snow Thrower Skid Shoe Safety Ignition KeyAuger Drive Control Chute Tilt ControlGas And Oil Fill-up Operating Your Snow ThrowerTrack Lock Lever Before StartingRecoil Starter To Stop EngineTo Engage Track Drive To Engage AugersOperating Tips Drift CuttersDrive Control and Shift Lever Chute AssemblyAuger Control Carburetor Shift Rod AdjustmentMaintaining Your Snow Thrower Skid ShoesAuger Bearings Drive / Auger Control LockGear Case Auger ShaftShave Plate and Skid Shoes Belt Removal And ReplacementServicing Your Snow Thrower AugersDrive Belt Replacing Friction Wheel RubberOff-Season Storage EngineProblem Cause Remedy TroubleshootingParts List for Model 730 STE Model 730 STE 2227 26 -0604A Hex Screw, 5/16-18 725-0157 Model 730 STE Model 730 STE Model 730 STE Track Steering Drive Shaft Model 730 STE MANUFACTURER’S Limited Commercial Warranty For MANUFACTURER’S Limited Warranty for

730 STE specifications

The Cub Cadet 730 STE is a powerful and versatile snow blower designed to tackle even the toughest winter conditions. Featuring a robust 24-inch clearing width, this snow thrower is engineered to handle heavy snowfall with ease. Its impressive throwing distance, which can reach up to 40 feet, makes it an ideal choice for both residential and commercial use. The 730 STE is equipped with a strong 277cc engine that provides reliable performance and the necessary power to push through packed snow and ice.

One of the standout features of the Cub Cadet 730 STE is its innovative track drive system. This advanced system ensures superior traction and stability on various surfaces, including steep inclines and uneven terrain. The track drive design gives users added confidence, allowing them to navigate snowy pathways and driveways without slipping or losing control.

The snow blower also incorporates a user-friendly control panel, allowing operators to easily manage speed settings and directional control. With multiple speed settings, the 730 STE enables users to adjust the pace for optimal efficiency based on the depth and type of snow being cleared. The highly maneuverable design of the snow blower makes it easy to work around obstacles such as mailboxes, fences, and landscaping.

Another remarkable feature of the Cub Cadet 730 STE is its adjustable chute. The 180-degree rotating chute allows users to direct the snow wherever they wish, ensuring efficient removal without worrying about blowing snow back onto already cleared areas. The chute is made from durable materials, enhancing its lifespan while maintaining effective performance.

Safety is also a priority in the design of the 730 STE. The snow blower comes with features such as a headlight for improved visibility during early morning or late evening snow clearing, making it safer to operate under low light conditions. Additionally, the durable and reinforced construction guarantees longevity and reliability throughout many winter seasons.

In summary, the Cub Cadet 730 STE stands out in the snow blower market with its powerful engine, superior traction, adjustable chute, and user-friendly controls. These characteristics make it an exceptional choice for anyone looking to tackle winter weather efficiently and effectively. Whether you're clearing your driveway or maintaining a commercial lot, the 730 STE is equipped to handle the task with performance and precision.
Top Page Image Contents