Cub Cadet 730 STE manual Engine, Off-Season Storage

Page 16

•Using a 7/8" wrench to hold the shaft, loosen, but do not completely remove, the hex bolt and bell washer on the left end of gear shaft. See Figure 20.

Hex Bolt &

Bell Washer

Track

Figure 20

•Lightly tap the hex nut to dislodge the ball bearing from the right side of frame before removing the hex nut and bell washer from left end of shaft.

•Move the gear shaft to the right and slide the friction wheel assembly from the shaft. See A.

•Remove the four screws from the friction wheel assembly. See B.

A

Shift Rod

 

Assembly

Spacer

Sprocket

 

 

Pin

 

Friction Wheel

Support

Assembly

 

Bracket

 

 

Shaft

B Screws

Friction Wheel Rubber

 

 

Hub

Friction Wheel

 

Plates

 

Figure 21

•Remove the friction wheel rubber from between the friction wheel plates.

•Reassemble new friction wheel rubber to the friction wheel plates and hub, tightening the four screws in rotation and with equal force.

•Position the friction wheel assembly up onto the pin of the shift rod assembly, and slide the shaft through the assembly. Reassemble in reverse order.

Engine

Refer to the separate engine manual packed with your unit for all engine maintenance procedures.

Off-Season Storage

WARNING: Never store the machine or fuel container indoors where there is an open flame, spark, or pilot light such as on water heater, furnace, clothes dryer, or other gas appliance.

WARNING: Drain fuel into an approved container outdoors, away from an open flame. Allow engine to cool. Extinguish cigarettes, cigars, pipes, and other sources of ignition prior to draining fuel. Fuel left in engine for extended periods deteriorates and will cause starting problems.

If unit is to be stored over 30 days, prepare for storage as follows:

•Remove gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine.

•Run engine until fuel tank is empty and engine stops due to lack of fuel.

•Drain carburetor by pressing upward on bowl drain, located below the carburetor cover.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Do not drain carburetor if using fuel stabilizer.

•Wipe equipment with an oiled rag to prevent rust.

•Remove spark plug and pour one ounce of engine oil through spark plug hole into cylinder. Cover spark plug hole with rag. Crank engine several times to distribute oil. Replace spark plug.

•Follow the lubrication recommendations found in the Maintenance Section.

•Always store the snow thrower in a clean, dry area.

NOTE: When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rust proof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings, and cables.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingPreparation OperationYour Responsibility Maintenance & StorageDo not modify engine Assembling Your Snow Thrower Know Your Snow Thrower Clean-Out ToolDrive Control / Auger Control Lock Safety Ignition Key Auger Drive ControlChute Tilt Control Skid ShoeOperating Your Snow Thrower Track Lock LeverBefore Starting Gas And Oil Fill-upTo Stop Engine To Engage Track DriveTo Engage Augers Recoil StarterDrift Cutters Operating TipsAuger Control Chute AssemblyDrive Control and Shift Lever Shift Rod Adjustment Maintaining Your Snow ThrowerSkid Shoes CarburetorDrive / Auger Control Lock Gear CaseAuger Shaft Auger BearingsBelt Removal And Replacement Servicing Your Snow ThrowerAugers Shave Plate and Skid ShoesReplacing Friction Wheel Rubber Drive BeltEngine Off-Season StorageTroubleshooting Problem Cause RemedyParts List for Model 730 STE Model 730 STE 2227 26 -0604A Hex Screw, 5/16-18 725-0157 Model 730 STE Model 730 STE Model 730 STE Track Steering Drive Shaft Model 730 STE MANUFACTURER’S Limited Commercial Warranty For MANUFACTURER’S Limited Warranty for

730 STE specifications

The Cub Cadet 730 STE is a powerful and versatile snow blower designed to tackle even the toughest winter conditions. Featuring a robust 24-inch clearing width, this snow thrower is engineered to handle heavy snowfall with ease. Its impressive throwing distance, which can reach up to 40 feet, makes it an ideal choice for both residential and commercial use. The 730 STE is equipped with a strong 277cc engine that provides reliable performance and the necessary power to push through packed snow and ice.

One of the standout features of the Cub Cadet 730 STE is its innovative track drive system. This advanced system ensures superior traction and stability on various surfaces, including steep inclines and uneven terrain. The track drive design gives users added confidence, allowing them to navigate snowy pathways and driveways without slipping or losing control.

The snow blower also incorporates a user-friendly control panel, allowing operators to easily manage speed settings and directional control. With multiple speed settings, the 730 STE enables users to adjust the pace for optimal efficiency based on the depth and type of snow being cleared. The highly maneuverable design of the snow blower makes it easy to work around obstacles such as mailboxes, fences, and landscaping.

Another remarkable feature of the Cub Cadet 730 STE is its adjustable chute. The 180-degree rotating chute allows users to direct the snow wherever they wish, ensuring efficient removal without worrying about blowing snow back onto already cleared areas. The chute is made from durable materials, enhancing its lifespan while maintaining effective performance.

Safety is also a priority in the design of the 730 STE. The snow blower comes with features such as a headlight for improved visibility during early morning or late evening snow clearing, making it safer to operate under low light conditions. Additionally, the durable and reinforced construction guarantees longevity and reliability throughout many winter seasons.

In summary, the Cub Cadet 730 STE stands out in the snow blower market with its powerful engine, superior traction, adjustable chute, and user-friendly controls. These characteristics make it an exceptional choice for anyone looking to tackle winter weather efficiently and effectively. Whether you're clearing your driveway or maintaining a commercial lot, the 730 STE is equipped to handle the task with performance and precision.
Top Page Image Contents