Cub Cadet 600 manual Chute Clean-Out Tool, Drift Cutters on models so equipped, Drift Cutter Kit

Page 13

Chute Clean-Out Tool

The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow and ice become lodged in the chute assembly during operation, proceed as follows to safely clean the chute assembly and chute opening:

•Release both the Auger Control and the Drive Control.

•Stop the engine by removing the ignition key.

•Remove the clean-out tool from the clip which secures it to the rear of the auger housing.

•Use the shovel-shaped end of the clean-out tool to dislodge and scoop any snow and ice which has formed in and near the chute assembly.

WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing

•Refasten the clean-out tool to the mounting clip on the rear of the auger housing, reinsert the ignition key and start the snow thrower’s engine.

•While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow and ice from the chute assembly.

Drift Cutters (on models so equipped)

Drift cutters should be used when operating the snow thrower in heavy drift conditions.

On models so equipped, drift cutters are assembled to the auger housing inverted. Remove the carriage bolts by unthreading the hex nuts which secure them, and reinstall the drift cutters in their proper position before operating the snow thrower. See Figure 12 .

If your unit is not equipped with drift cutters, contact Customer Support as instructed on page 2 for information regarding price and availability.

Snow Thrower Model

Drift Cutter Kit

All models

OEM-390-679

.

Drift

Cutter

Carriage Screws /

Hex Nuts

Figure 12

Tire Chains (on models so equipped)

Tire chains should be used whenever extra traction is needed. If your unit is not equipped with tire chains, contact Customer Support for information regarding price and availability.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of the muffler and the surrounding areas may exceed 150°F(65° C). Avoid these areas.

•If possible, remove snow immediately after it falls.

•Discharge snow downwind whenever possible.

•Slightly overlap each previous path.

•Set the skid shoes 1/4" below the shave plate for normal usage. Adjust it upward for hard-packed snow and downward when using on gravel or crushed rock.

•Avoid possible starter freeze-up. Clean the snow thrower thoroughly after each use.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Series Snowthrowers Table of Contents Training Important Safe Operation PracticesYour Responsibility Maintenance And StorageBefore Assembly Setting UP Your Snow ThrowerSetting up the Snow Thrower UnpackingFor Models with 4 Way Chute Control Box Chute Assembly all modelsFinal Adjustments Chute Clean-out ToolSkid Shoe Throttle Control Knowing Your Snow ThrowerPrimer Oil FillAuger Control Clean-Out ToolWay Chute Control optional Chute Directional Control optionalOperating Your Snow Thrower To Engage Drive Stopping The EngineTo Engage Augers For models with optional interlock mechanism onlyOperating Tips To Throw SnowDrift Cutters on models so equipped Chute Clean-Out ToolDrift Cutter Kit Tire Chains on models so equippedChute Bracket Adjustment Shift Rod AdjustmentSkid Shoes Lubrication EngineShave Plate and Skid Shoes AugersAuger Belt Replacing BeltsDrive Belt Friction Wheel Rubber OFF-SEASON Storage Trouble Shooting Tractor Attachment Warranty Three 3 Year Limited WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Part RÉF Pièce Description Page Part RÉF Pièce Description For models with 22 auger housings Part RÉF Pièce Description Styles H, K & L 31a-6006 Commerciale Utilisation Dépannage DE Guide 8 Chapitre Saison Hors Remisage 7 Chapitre Caoutchouc en bague la de Changement Frottement de roue la deFigure la Voir .le-écartez et Patins et plate Lame Courroies les de RemplacementIllustrée po 30 de Tarière -21 Figure Moteur LubrificationTransmission la de Commande Tarière la de CommandePatins Patins 19 FigureVitesses de levier du Tige Réglages 5 ChapitreGoulotte Pneu pour Chaînes ’utilisation ConseilsCoupe de Barres Goulotte la de dégagement de OutilTarière la embrayer Pour Neige la projeter PourMoteur du Arrêt Transmission la embrayer PourTarières GoulotteLanceur à démarreur de Poignée Option en fonctions 2 à goulotte la de Commande Tarière la de CommandeOption en fonctions 4 à goulotte la de Commande ’entraînement de CommandeAmorceur ’obturateur de CommandeDépart de Volet Neige la de dégagement de Outil «Réglage» chapitre le dans goulotte» Souffleuse la de Assemblage Montage 2 Chapitre’assemblage Avant Carton du DéballageResponsabilité Votre Remisage ET Entretien Formation PréparationChapitre VENTE-APRÈS Service600 séries Souffleuses

600 specifications

The Cub Cadet 600 series represents a significant innovation in the realm of lawn care and gardening, catering to homeowners and professional landscapers alike. This standout line of riding lawn mowers combines powerful performance with advanced technology, rendering it a top choice for those aiming for beautifully manicured lawns.

At the heart of the Cub Cadet 600 is a robust engine that delivers exceptional power and reliability. Featuring a range of engine options, users can select the horsepower that best suits their mowing needs. The efficient fuel system optimizes performance and minimizes emissions, adhering to modern environmental standards.

One of the major highlights of the Cub Cadet 600 is its cutting system. Equipped with a precision-engineered deck, it allows for a clean, even cut on various types of terrain. The adjustable cutting height features multiple positions, giving users the flexibility to tackle different grass lengths and types seamlessly. The stamped steel construction of the deck ensures durability and longevity, making it resistant to wear and tear over time.

The 600 series also boasts advanced technology such as the Cub Cadet Smart Jet cleaning system, which simplifies maintenance by ensuring the mower deck is free of grass clippings and debris. This system promotes optimum performance and extends the life of the mower.

Ergonomics play a vital role in the design of the Cub Cadet 600. The operator's station is crafted for comfort, featuring an adjustable seat with ample cushioning. The intuitive control layout allows for easy operation, making it accessible for users of all experience levels. Additionally, the steering wheel is designed for enhanced maneuverability, especially in tight spaces.

To enhance productivity, the Cub Cadet 600 includes a tight turning radius, allowing for excellent maneuvering around obstacles. Users can navigate gardens, flower beds, and trees with ease, minimizing the need for additional trimming.

The series also supports a range of accessories such as baggers, mulch kits, and towing attachments, further increasing its versatility. This adaptability makes the Cub Cadet 600 not just a mower, but a comprehensive landscaping tool.

In summary, the Cub Cadet 600 combines power, precision, and user-friendly features, making it an exceptional choice for anyone looking to maintain their lawn with professionalism. With its advanced technologies and rugged construction, the 600 series stands out as a leader in modern lawn care solutions.
Top Page Image Contents