Craftsman 536.88502 owner manual Ass Ly, To Remove Snow Thrower, HOW to SET UP Your Snow Thrower

Page 7

ii,

i

ill

ii,lll

,

illlll,lll

iiilll

i

ill

ASS LY

Figure I shows the snow thrower in the shipping position Figure 2 shows the snow thrower completely assembled

Reference to the right and left hand side of the snow thrower is from the operator's position at the handte_

TO REMOVE SNOW THROWER

FROM CARTON (See Fig 1)

eCut all four corners q_the carton fr0omtop to bottom and lay the panels flat..

•Cut the cable ties attached to the augers..

eCut and discard the ties that secure the crank assembly and place the assembly aside

•Remove the packing materialfromthe controlpaneL

=Cut and discard the packing securing the clutch cables to the lower handle1

®With two 9/16 inch wrenches, loosen (do not re- move) both bolts securing the upper and lower handles Swing the upper handle into the operating position.

NOTE: if the cables have become disconnected from the clutch levers, reinstall the cables as shown in Figure 3.

eTighten both bolts securely.

eRoll the snow thrower of{ the skid by pulling on the handle.

NOTE: This snow thrower is equipped with a track drive and can be hard to push when the engine is not running. it is easier to pull the snow thrower backward if it must be moved without the engine running

The drive system may be tight when you first use your snow thrower. It loosens up as you use it.

illll,i i i,,i

iHi ii

CONTROL

LOWER HANDLEPANEL

CRANK

ASSEMBLY

CLUTCH

CABLE

UPPER

HANDLE

ASSEMBLY

HOW TO SET UP YOUR SNOW

THROWER

TO SET THE SKID HEIGHT

For shipping, the height adjust skids are reversed To use your snow thrower, you need to remove the height adjust skids and reinstall as shown in Fig. 2 Then adjust the height adjust skids for surface conditions as follows:

"Z" FITTING

QLoosen the mounting nuts on the skids (See Fig. 2).

OPlace the extra shear bolts (in the parts bag) under

each end of the scraper bar near but not under the skids.

•Push each skid up or down until it touches the ground and the scraper bar is resting on each shear bolt. Be sure the skids are set at the same height on both sides

•Tighten the mounting nuts

TRACTION

DRIVE

LEVER

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Owners Manual Before USE Fuel SafetyREPA1RtADJUSTMENTS Safety Safety RulesSpark Plug Horse PowerDisplacement JSCIndex Table of ContentsL,lal l lJl l,l!i Contents of Shipping Carton Tools Required for AssemblyTo SET the Skid Height HOW to SET UP Your Snow ThrowerASS LY To Remove Snow ThrowerTo CHECK/ADJUST Control Cables To iNSTALL Upper Handle and Crank AssemblyTo Install the Shifter Lever Knob AssemblyTo Install Headlight Sembly INCORRECTt.Y and Snow could be DIS Chute FlangeThrower OperationTo .,ONTROL Snow Discharge HOW to USE Your Snow ThrowerTo Throw Snow OFF To USE Weight Transfer SystemBefore Starting the Engine Fill GASGrounded Receptacle First OperationTo Stop Engine Warm StartChoke Control To Stop EngineFrozen Recoil Starter Doors or in ENCLOSED, Poorly Ventilated AREAS. Engine EXSnow Throwing Tips OperatioMove Throttle Lever to Stop POSI- Tion After First USE TenanceGeneral Recommendations Snow ThrowerSpark Plug EngineDipstick To Adjust Chute Crank Assembly AdjustmentsTo Adjust Skids Height To Adjust Scraper BARPulley Service ANAdjust To Adjust BeltsAuger Drive Belt To Replace BeltsTrack Drive Belt ServiceAdjust TS Loosenbo Trackconnectingrod Frictionwheel DiscdriveplateTo Replace Friction Wheel Service and AdjustmentsTo Replace Auger Shear To Adjust TrackFIGo40 To Adjust CarburetorTo Adjust or Replace Spark Plug To AdjustEngine Engine StorageSnow Thrower Storage OtherLubrication Chart ServiceSchedule Correction Trouble CausePage 73 3 1 3 Craftsman 32 TRAC-PLUS Snow ThrowerRER Craftsman 32 TRAC-PLUS SnowNO. Part NO, Part Name 76 83 85 Craftsman 32 TRAC-PLUS Snow ThrowerNO. Part no REFoPart Name Track Assembly Repair Parts 71037 Idler Wheel132 TRAC-PLUS Snow CraftsmanBearing REF.IRing Quad 59O628 Rewind Starter NOoFtsmah =CY=E Engin CRAFTSMAN4-CYCLEEHGINE Carburetor 33377396 40OPage Engine Model Number Part Number Part Description When Ordering Repair PARTS, AlwaysGive the Following Information Product Snow Thrower Model Number
Top Page Image Contents