Craftsman 536.88502 owner manual Assembly, To Install the Shifter Lever Knob, To Install Headlight

Page 9

J ,,,,, i

_ ,,,,,,,,

1,1,,,

,,I,H,

.... ,,,

=1,=,,=,

,,,,,

,

,

,, ,,

 

 

 

 

ASSEMBLY

 

 

 

 

.....................................ii

,,1,,

,,,

,,,

TO INSTALL THE SHIFTER LEVER

KNOB

Stand the snow thrower up on the front of the auger housing, as shown in Fig 6A,

Cut the plastic tie which holds the shifter lever assembly to the shift bracket (Fig 6B).

Remove the Iocknut, washer, spring and bolt (Fig. 6D) ....

Reposition the shifter lever into the slot in the control panel, as shown in Fig 6C and reinstall the bolt, spring, washer and tocknut.

Tighten the Iocknut until t/8" to 3/16" (2 or 3 threads) of the bolt protrude past the locknut.

Thread the shifter lever knob onto the threaded endof the shifter lever until it is tight (Fig 6D)

OMovethe shifter lever through allthe speedsto ensure proper tension of the spring,, If the shifter lever sticks in any of the notches, loosen the Iocknut 1/4 turn at a time until the shifter lever moves freely.

,

,H,,,,,,,

=,,,i

N,,,,,

=1=,,,

,,

i,,,,,

 

H,,,

H,

 

,,,,,,,,,!,

 

i i ,,,,,,,,,,,

SHIFTER

BRACKET

TO INSTALL HEADLIGHT

The headlight is mounted on right side of upper handle and is installed upside down for shipping purposes

@Remove the pivot bolt (Fig., 7A), ptace headlight in correct position (as shown in Fig. 7B and in Fig 2) and retighten nut.

Tie the headlight cable to upper and lower handles with the plastic cable ties supplied in the parts bag by threading the pointed ends ot each tie through the square ends and pulling tightly around the headlight cable and the handle.,

NOTE: One side of the plastic tie has small notches in it, while the other side is smooth The notched side must be

on the inside of the loop which is formed when the ends are put together

@Tryto _oosen the cable tie If it can be loosened, it has been attached with the smooth side on the inside of the loop, Remove the cabletie and reverse itsdirection

O Cut off excess cable tie,

LOCKNUT

WASHI

1/8 TO 3/16 INCH OF EXPOSED THREADS

FIG, 6

FIG. 7A

FIG. 7B

Image 9
Contents Owners Manual Before USE Fuel SafetyREPA1RtADJUSTMENTS Safety Safety RulesDisplacement Horse PowerJSC Spark PlugIndex Table of ContentsL,lal l lJl l,l!i Contents of Shipping Carton Tools Required for AssemblyASS LY HOW to SET UP Your Snow ThrowerTo Remove Snow Thrower To SET the Skid HeightTo CHECK/ADJUST Control Cables To iNSTALL Upper Handle and Crank AssemblyAssembly To Install the Shifter Lever KnobTo Install Headlight Sembly INCORRECTt.Y and Snow could be DIS Chute FlangeThrower OperationHOW to USE Your Snow Thrower To .,ONTROL Snow DischargeTo Throw Snow Before Starting the Engine To USE Weight Transfer SystemFill GAS OFFTo Stop Engine OperationWarm Start Grounded Receptacle FirstFrozen Recoil Starter To Stop EngineDoors or in ENCLOSED, Poorly Ventilated AREAS. Engine EX Choke ControlOperatio Snow Throwing TipsMove Throttle Lever to Stop POSI- Tion General Recommendations TenanceSnow Thrower After First USEEngine Spark PlugDipstick To Adjust Skids Height AdjustmentsTo Adjust Scraper BAR To Adjust Chute Crank AssemblyAdjust Service ANTo Adjust Belts PulleyAuger Drive Belt To Replace BeltsAdjust TS ServiceLoosenbo Trackconnectingrod Frictionwheel Discdriveplate Track Drive BeltTo Replace Friction Wheel Service and AdjustmentsTo Replace Auger Shear To Adjust TrackTo Adjust or Replace Spark Plug To Adjust CarburetorTo Adjust FIGo40Snow Thrower Storage Engine StorageOther EngineService Lubrication ChartSchedule Correction Trouble CausePage 73 3 1 3 Craftsman 32 TRAC-PLUS Snow ThrowerCraftsman 32 TRAC-PLUS Snow RERNO. Part NO, Part Name 76 83 85 Craftsman 32 TRAC-PLUS Snow ThrowerREFo NO. Part noPart Name Track Assembly Repair Parts 71037 Idler Wheel132 TRAC-PLUS Snow CraftsmanREF.I BearingRing Quad 59O628 Rewind Starter NOoFtsmah =CY=E Engin CRAFTSMAN4-CYCLEEHGINE 396 3337740O CarburetorPage Give the Following Information Product Snow Thrower When Ordering Repair PARTS, AlwaysModel Number Engine Model Number Part Number Part Description