Craftsman 536,884,791 manual Warm Start, Above, Frozen Recoil Starter, Snow Throwing Tips

Page 12

Push the primer button, see figure on page 8, while covering the vent hole as follows: (remove finger from primer but- ton between primes).

One time if temperature is above 50oF.

Two times if temperature is 50_F to 15°t:.

Four times if temperature is below

15°F.

Pull the recoil starter handle rapidly. Do not allow the handle to snap back, but al-

tow it to rewind slowly while keeping a firm hold on the starter handle.

As engine starts warms up move choke lever to "1/2 choke" position. When engine runs smoothly, move choke lever to "No Choke" Position.

NOTE: Allow the engine to warm up for several minutes before blowing snow in

temperatures below 0°F.

Run the engine at full throttle "_ (Fast) when throwing snow.

WARM START

If restarting a warm engine after a short shutdown, leave choke at (Off) and do not push the primer button. If the engine fails to start, follow the Cold Start instructions

above.

FROZEN RECOIL STARTER

If the starter is frozen and will not turn engine:

Pull as much rope out of the starter as possible.

Release the starter handle and let it snap back against the starter.

If the starter still fails to turn engine, repeat the two previous steps until the starter en- gages. Then continue with the directions for cold start.

To help prevent possible freeze-up of recoil starter and engine controls, proceed as fol- lows after each snow removal job.

With the engine running, pull the starter

rope hard with a continuous full arm stroke three or four times. Pulling of

starter rop_ will produce a _oud clattering sound. This is not harmful to the engine

or starter.

With the engine not running, wipe all snow and moisture from the carburetor cover in area of control levers. Also move throttle control, choke control, and starter handle several times.

SNOW THROWING TIPS

For maximum snow thrower efficiency

operate engine at (Full) throttle. The en- gine is designed to deliver maximum performance at full throttle and should be run at this power setting at all times.

Most efficient snow throwing is accom- plished when the snow is removed immediately after it falls.

For complete snow removal, slightly overlap each path previously taken.

The snow should be discharged down wind whenever possible.

After the snow throwing job has been completed, allow the engine to idle for a few minutes, which wilt melt the snow and accumulated ice off the engine.

Clean the snow thrower thoroughly after each use.

Remove ice and snow accumulation and all debds from the entire snowthrower,

and flush with water (if possible) to re- move all salt or other chemicals. Wipe

snow thrower dry.

GENERAL RECOMMENDATIONS

The warranty on this snow thrower does not cover items that have been subjected to op-

erator abuse or negligence. To receive full

vatue from the warranty, the operator must maintain the snow thrower as instructed in this manual. The chart on the next page is

provided to assist the operator in properly maintaining the snow thrower.

Some adjustments will need to be made pe- (todicatty to propedy maintain your snow thrower.

12

Image 12
Contents Snow Thrower SEARS, Roebuck and CO., Hoffman Estates, IL 60179 U.S.ALimited TWO-YEAR Warranty on Craftsman Snow Thrower California PropositionOperation Disengage the auger/impeller, stop engine, and remove keyMaintenance and Storage Spare Spacers 16 In. Hsx Nuts Shear PinsTools Required for Assembly Parts packed separately in carton not shown full sizeTo Remove Snow Thrower From Carton To Install the Upper Handle and Crank Assembly Protective16 Hex Head Nut To CHECK/ADJUST Clutch Control Cable To Assemble Snow ChuteHex Nylon Lever ControlCable..jKnow Your Snow Thrower Fuel HOW to USE Your Snow Thrower To Stop Your Snow Thrower To Control Snow Discharge To Move Forward ElectricStarterBefore Starting the Engine Checkthe OILTo Start Engine Electric Starter Fill GASDo not prime if temperature is above Primer ButtonThree-hole, grounded 120 volt A.C ReceptacleWarm Start AboveFrozen Recoil Starter Snow Throwing TipsCustomer Responsibilities Service Schedule Records Dates Product Specifications Horse Power 5HP DisplacementSnow Thrower Engine Lubrication Snow Thrower After First USETo Adjust the Clutch Control Cable OIL RecommendationSpark Plug To Adjustthe Belt Guide To Adjust Auger Drive BeltTo Replace Belt To Adjust Carburetor To Adjust or ReplacetheSparkplug To Replace Auger Shear BoltEngine Storage Snow Thrower StorageUnits fails to Propel itselfTrouble Cause Correction