Craftsman 536,884,791 manual Maintenance and Storage, Spare Spacers 16 In. Hsx Nuts Shear Pins

Page 4

16. Neverdirectdischargeat bystanders or

allow anyone in front of the snow thrower.

17.Disengage power to the auger/impeller when snow thrower is transported or not in use.

4.Maintain or replace safety and instruc- tion labels, as necessary.

5.Run the snow thrower a few minutes after throwing snow to prevent freeze- up of the auger/impeller.

18.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as tire chains, electric start kits, etc).

19.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

MAINTENANCE AND STORAGE

1.Check shear bolts and other bolts

frequently for proper tightness to be sure the snow thrower is in safe

working condition.

2.Never store the snow thrower with fuel

in the fuel tank inside a building where ignition sources are present such as hot water and space heaters, clothes dryers, and the like. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator's manual instructions for important details if the snow thrower is to be stored for an

/_k WARNING: This snow thrower is for

use on sidewalks, driveways and other ground level surfaces.

Caution should be exercised while using on steep sloping surfaces. DO NOT USE

SNOW THROWER ON SURFACES ABOVE GROUND LEVEL such as roofs of residences, garages, porches or other such structures or buildings.

extended

period.

 

 

 

 

Contents of

Parts

Bag

 

 

 

-Owner'sManual (not shown)

 

 

 

11- Fuel Stabilizer(not shown)

 

 

 

1 - Warranty Card (not shown)

_

I

_

2- Parts Bags (not shown)

I

\\

* Non-AssemblyPartsare found in your Tool Box located

I

I

\\

 

 

*2Do-

II

 

on top of your belt cover.

 

 

 

 

 

Spare Spacers

I

 

 

2 - 5/16 In. Hsx Nuts

 

/_1_

 

 

(_

_J

 

*2 - Shear Pins

 

_

_1

" _tatdehoMw°nt°rcC°a_dize)

3 - Carriage

Bolts, 5/16-18xl

.00 In.

5 - Flatwashers

11/32 In.

3 -HexNylon Nuts, 5/16-18

4

Image 4
Contents Snow Thrower SEARS, Roebuck and CO., Hoffman Estates, IL 60179 U.S.ALimited TWO-YEAR Warranty on Craftsman Snow Thrower California PropositionOperation Disengage the auger/impeller, stop engine, and remove keyMaintenance and Storage Spare Spacers 16 In. Hsx Nuts Shear PinsParts packed separately in carton not shown full size Tools Required for AssemblyTo Remove Snow Thrower From Carton Protective To Install the Upper Handle and Crank Assembly16 Hex Head Nut To CHECK/ADJUST Clutch Control Cable To Assemble Snow ChuteHex Nylon Lever ControlCable..jKnow Your Snow Thrower FuelHOW to USE Your Snow Thrower To Stop Your Snow Thrower To Control Snow DischargeTo Move Forward ElectricStarterBefore Starting the Engine Checkthe OILTo Start Engine Electric Starter Fill GASDo not prime if temperature is above Primer ButtonThree-hole, grounded 120 volt A.C ReceptacleWarm Start AboveFrozen Recoil Starter Snow Throwing TipsCustomer Responsibilities Service Schedule Records Dates Product Specifications Horse Power 5HP DisplacementSnow Thrower Engine Lubrication Snow Thrower After First USEOIL Recommendation To Adjust the Clutch Control CableSpark Plug To Adjust Auger Drive Belt To Adjustthe Belt GuideTo Replace Belt To Adjust Carburetor To Adjust or ReplacetheSparkplug To Replace Auger Shear BoltEngine Storage Snow Thrower StoragePropel itself Units fails toTrouble Cause Correction