Craftsman 486.24837 manual See Figure, Engagement ROD Suspension ARM, Tensioning Chain

Page 16

iNSTALLiNG CLUTCH/IDLER ASSEMBLY

This section covers the installation of the Clutch/Idler assembly to tractors with attachment clutches that are either rod operated (p. 16), cable operated (p. 18) or

electric (p. 20). Use the appropriate instructions for your tractor.

ROD OPERATED MANUAL ATTACHMENT CLUTCH

STEP 29: (SEE FIGURE 29)

Move the attachment clutch lever on the dash panel to

the disengaged (down) position.

Screw the trunnion onto the end of the snow thrower engagement rod.

Locate the clutch arm (where the mower clutch rod was connected) underneath the right hand side the tractor, just to the inside of the suspension arm. If there is an extension attached to the clutch lever, the extension, bolt and nut must be removed and stored with the mower deck.

IMPORTANT: Re=attach the extension to the clutch lever before reinstalling the mower deck.

Position the engagement rod to the inside of the clutch arm and insert the drilled end of the rod

through the arm. Secure with a 5/64" hairpin cotter.

TRACTOR'S CLUTCH ARM

ENGAGEMENT ROD

/

\

SUSPENSION ARM

5/64" HAIRPIN COTTER

REMOVE EXTENSION,

BOLT AND NUT

(IF PRESENT)

FIGURE 29

RIGHT SIDE VIEW

STEP 30: (SEE FIGURE 30)

Attach the two rear pulley frame brackets to the inside of the clutch/idler assembly using two 5/16" x 1" hex

bolts, eight 5/16" washers and two 5/16" nylock nuts for each bracket.

Attach the two front pulley frame brackets to the inside of the clutch/idler assembly using two 5/16" x 3/4" hex bolts, 5/16" washers and 5/16" nylock nuts for each bracket. Add extra washers if needed.

Insert a tensioning chain through the hole shown and attach the end link to the spring on the lower idler arm.

5116"x 3/4" HEX BOLT

5/16"

WASHER

/

5/16"

x 1"

 

 

HEX BOLT

/

/

(4) 5/16" WASHERS

 

 

 

TENSIONING CHAIN

 

5/16" NYLOCK NUT

 

(lower idler arm)

FIGURE

30

 

 

STEP 31: (SEE FIGURE 31)

Three different length drive belts are included with your snow thrower. Tractors with manual attachment clutches and dual front deck suspension brackets use the 55" drive belt with #46989 printed on the outside of the belt. DO NOT USE the other belts.

Slightly loosen the hex bolt next to the flat idler pulley. Install the drive belt down between the hex bolt and the flat idler pulley with the flat side of the belt against the pulley. Retighten the hex bolt.

Loop the belt around the large v-pulley, placing it between the v-pulley and the hex bolt next to the pulley.

HEX BOLTS

FLAT IDLER

PULLEY

#46989 ,/_

DRIVE BELT

FIGURE 31

Did you choose the correct drive belt for your tractor? Using the wrong length belt may cause premature bearing or belt failure.

16

Image 16
Contents CRRFr. MgN Do not Return to StoreWheel Weight ONE Year Full WarrantySnow CAB Alert!!Your safety is involved Shown Actual Size QTY Not ShownDescription Only Items Needed for Model 917. Tractors are Shown Tools Required for Assembly Locate Tractors Model LabelRemoval of Parts from Carton Tractor PreparationBracket Identifyyour Tractor See FigureRemove Front Screws Browning Shield Right Side ViewNUT FlangedLeft Side ViEW This Section is for Tractors with a If your tractor has an electric attachment clutch go to16 x HEX Bolt WashersSEEFIGURE11 TractorsBracket Hanger Shoulder5116 This Section is for Tractors with ANNylock NUT Cotter See Figure CLUTCH/IDLER AssemblyShoulder Front Deck Suspension Brackets Fasten Side Plates to TractorSuspension ARM HangerCarriage Bracket Bolt Left Side ViewEngagement ROD Suspension ARM See FigureTensioning Chain SEEFIGURE32 CLUTCH/IDLER AssemblyUse second Hole Cableoperatedmanual Attachment Clutch See Figure NUT See Figure16 x 3/4 HEX Bolt HEX BoltSEEFIGURE38 5164HAIRTractors Clutch Cable Hairpin Cotter See FigureElectricattachmentclutches SEEFIGURE41 5116 x 3/4 HEX BoltWasher 5116 xHairpin Cotter Pivot Lock PiNAssembly of the Snow Thrower DISCHARGE\\\SEEFIGURE51 SpiralHEX Bolt ANTI=ROTATION Plastic CAPINSTALLiNG the Auger Belt Attaching Snow Thrower to TractorRear PulleyInstalling the Attachment PIN Refer Backto on ChecklistSetting the Auger Belt Tension HOW to Startyour Snow Thrower HOW to Stop Your Snow ThrowerHOW to USE Your Snow Thrower Know YOU R Snow TH RowerLubrication RaisingandloweringCheck Scraper and Shoes for Wear Clutch Disengagement Adjustment Replacing Auger BeltSpiral Augers Shear BORemoving the Spiral Auger Housing ProblemStorage Recommendations Parts to Remove AT END of Season CauseRepair Parts for Model 486.24837 42 Snow Thrower QTY Description 59--C REF Part no REF Part no QTY QTYFold Along D Only Ride UP and Down Hill Not Across Hill Degrees MAXMY-HOME

486.24837 specifications

The Craftsman 486.24837 is a versatile outdoor power equipment tool that has garnered attention for its efficient performance and user-friendly features. Designed primarily for homeowners and gardening enthusiasts, this model serves as a reliable solution for various landscaping tasks, such as mowing lawns, managing garden beds, and trimming hedges.

One of the standout features of the Craftsman 486.24837 is its robust engine, which provides ample power to handle tougher jobs with ease. Equipped with a powerful motor, it enables users to tackle thick grass and harsh terrain that would typically challenge lesser models. The engine's efficient fuel consumption further enhances its usability, enabling prolonged use without frequent refueling.

In terms of cutting performance, the Craftsman 486.24837 incorporates an adjustable cutting height feature. This allows users to customize the height setting according to their specific needs, whether they are looking for a close trim or a more lifted finish for their lawns. The extended cutting deck ensures a wider cutting path, enabling quicker mowing, hence reducing overall time spent on yard tasks.

Durability is a key aspect of the Craftsman 486.24837. Constructed with high-quality materials, it is designed to withstand the rigors of outdoor use. The sturdy build ensures that the machinery retains its efficiency and effectiveness over time, making it a worthwhile investment for regular maintenance.

The ergonomics of the Craftsman 486.24837 also deserve mention. With a comfortable grip and user-friendly controls, it minimizes user fatigue during prolonged use, allowing for smooth operation. The lightweight design enhances maneuverability, ensuring that both novice users and seasoned gardeners can operate it with confidence and ease.

In addition to its primary features, the Craftsman 486.24837 includes technologically advanced elements such as easy start mechanisms and safety features. These enhancements prioritize user safety while also making the operation more accessible for everyone.

In conclusion, the Craftsman 486.24837 stands out as a reliable, efficient, and easy-to-use outdoor power equipment. With features designed to improve cutting efficiency, durability, and user comfort, it serves as an invaluable tool for homeowners looking to maintain their outdoor spaces effectively. Its combination of power and practicality makes it a popular choice among gardening enthusiasts and landscape professionals alike.