Husqvarna 1827EXLT warranty Snow Throwing Tips, Before Stopping, If Recoil Starter has Frozen

Page 15

OPERATION

8.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” position.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.

It is easier and more efficient to remove snow imme- diately after it falls.

The best time to remove snow is the early morning. At this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures.

Slightly overlap each successive path to ensure all snow will be removed.

Throw snow downwind whenever possible.

Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

15

Image 15
Contents Operator’s Manual Safe Operation Practices for Walk-Behind Snow Throwers Shut the Engine OFF Clearing a Clogged Discharge ChuteTable of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsTo Transport See Figs Transport and Height Adjustment of Snow ThrowerHOW to USE Your Snow Thrower SET Height Adjustment See FigsTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigScraper BAR See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigADD Gasoline See Fig Before Starting the EngineTo USE Drift Cutters See Fig Check Engine OIL Level See FigSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Before Each USE Maintenance➀ SAE 30 Motor Oil ➁ See Engine Maintenance section General RecommendationsCleaning Snow ThrowerEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Tracks See Fig CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction TroubleshootingLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Qjlqh 7UDQVPLVVLRQ Service Notes 08/01/2011 SR

1827EXLT specifications

The Husqvarna 1827EXLT is a robust snow thrower designed to tackle harsh winter conditions with ease and efficiency. With its powerful engine and advanced features, it promises performance and reliability, making it an ideal choice for homeowners who need to clear driveways, walkways, and large areas of snow.

Equipped with a 272cc Husqvarna engine, the 1827EXLT provides an impressive output, ensuring that it can handle heavy and wet snow without any issues. The engine is designed for easy starting, even in cold weather conditions, making winter maintenance a hassle-free experience.

One of the standout features of the 1827EXLT is its two-stage snow throwing mechanism. This design utilizes an auger to collect snow, which is then propelled by an impeller through the chute. The result is efficient snow removal, where the snow can be thrown up to 33 feet away. This extended throwing distance ensures that you can clear large areas without needing to move snow back into already cleared sections.

The snow thrower boasts a clearing width of 27 inches, making it capable of handling wider paths and driveways in fewer passes. The adjustable skid shoes provide customization to the height at which the machine operates, allowing you to prevent damage to surfaces while effectively clearing snow.

The 1827EXLT also features a friction disc transmission that enables smooth speed changes, ensuring a comfortable operation. With six forward and two reverse gears, users can easily navigate various terrains and adapt to changing conditions.

Furthermore, the snow thrower is designed with user comfort in mind. It features heated grips, which significantly enhance the operator's comfort during prolonged use in cold conditions. The easy-to-use control panel provides quick access to all the essential functions, including chute rotation and deflection controls, enhancing the user's experience.

Durability is another big selling point of the Husqvarna 1827EXLT. Its heavy-duty steel frame and high-strength plastic components ensure long-lasting performance and resistance against wear.

In conclusion, the Husqvarna 1827EXLT is a powerful and reliable snow thrower that combines advanced features and user-friendly technology. It is perfect for those who need a dependable machine to keep their outdoor spaces clear during winter, ensuring practicality and efficiency in snow removal tasks. Whether dealing with heavy snowfalls or light dustings, the 1827EXLT stands ready to handle the job.