Husqvarna 1827EXLT warranty Snow Thrower, Engine, Cleaning

Page 17

MAINTENANCE

SNOW THROWER

Always observe safety rules when performing maintenance.

TRACKS

•Keep track belt free of gasoline / oil, which can harm rubber.

BELTS

Check belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs atten- tion is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

Do not lubricate or add oil to the hydrostatic transmission inside your snow thrower. This is a closed system and does not require maintenance.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side track may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left track removed, will help drain any oil trapped inside the engine. (See “TO REMOVE TRACKS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left track (if removed for draining oil). Be sure to install klik pin into hole in axle (See “TO REMOVE TRACKS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

•Keep finished surfaces/track belt free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operator’s Manual Safe Operation Practices for Walk-Behind Snow Throwers Shut the Engine OFF Clearing a Clogged Discharge ChuteTable of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsHOW to USE Your Snow Thrower Transport and Height Adjustment of Snow ThrowerSET Height Adjustment See Figs To Transport See FigsTo USE Fuel SHUT-OFF Valve See Fig Using the CLEAN-OUT Tool See FigTo USE Choke Control See Fig To Throw Snow See FigTo Adjust Skid Plates See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Scraper BAR See FigTo USE Drift Cutters See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping ➀ SAE 30 Motor Oil ➁ See Engine Maintenance section MaintenanceGeneral Recommendations Before Each USEEngine CleaningSnow Thrower To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Tracks See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILProblem Cause Correction TroubleshootingLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Qjlqh 7UDQVPLVVLRQ Service Notes 08/01/2011 SR

1827EXLT specifications

The Husqvarna 1827EXLT is a robust snow thrower designed to tackle harsh winter conditions with ease and efficiency. With its powerful engine and advanced features, it promises performance and reliability, making it an ideal choice for homeowners who need to clear driveways, walkways, and large areas of snow.

Equipped with a 272cc Husqvarna engine, the 1827EXLT provides an impressive output, ensuring that it can handle heavy and wet snow without any issues. The engine is designed for easy starting, even in cold weather conditions, making winter maintenance a hassle-free experience.

One of the standout features of the 1827EXLT is its two-stage snow throwing mechanism. This design utilizes an auger to collect snow, which is then propelled by an impeller through the chute. The result is efficient snow removal, where the snow can be thrown up to 33 feet away. This extended throwing distance ensures that you can clear large areas without needing to move snow back into already cleared sections.

The snow thrower boasts a clearing width of 27 inches, making it capable of handling wider paths and driveways in fewer passes. The adjustable skid shoes provide customization to the height at which the machine operates, allowing you to prevent damage to surfaces while effectively clearing snow.

The 1827EXLT also features a friction disc transmission that enables smooth speed changes, ensuring a comfortable operation. With six forward and two reverse gears, users can easily navigate various terrains and adapt to changing conditions.

Furthermore, the snow thrower is designed with user comfort in mind. It features heated grips, which significantly enhance the operator's comfort during prolonged use in cold conditions. The easy-to-use control panel provides quick access to all the essential functions, including chute rotation and deflection controls, enhancing the user's experience.

Durability is another big selling point of the Husqvarna 1827EXLT. Its heavy-duty steel frame and high-strength plastic components ensure long-lasting performance and resistance against wear.

In conclusion, the Husqvarna 1827EXLT is a powerful and reliable snow thrower that combines advanced features and user-friendly technology. It is perfect for those who need a dependable machine to keep their outdoor spaces clear during winter, ensuring practicality and efficiency in snow removal tasks. Whether dealing with heavy snowfalls or light dustings, the 1827EXLT stands ready to handle the job.
Top Page Image Contents