Husqvarna 1827EXLT warranty Storage, Other, Fuel System, Engine OIL, Cylinder

Page 21

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operator’s Manual Safe Operation Practices for Walk-Behind Snow Throwers Shut the Engine OFF Clearing a Clogged Discharge ChuteTable of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsHOW to USE Your Snow Thrower Transport and Height Adjustment of Snow ThrowerSET Height Adjustment See Figs To Transport See FigsTo USE Fuel SHUT-OFF Valve See Fig Using the CLEAN-OUT Tool See FigTo USE Choke Control See Fig To Throw Snow See FigTo Adjust Skid Plates See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Scraper BAR See FigTo USE Drift Cutters See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen ➀ SAE 30 Motor Oil ➁ See Engine Maintenance section MaintenanceGeneral Recommendations Before Each USECleaning Snow ThrowerEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Tracks See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILProblem Cause Correction TroubleshootingLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Qjlqh 7UDQVPLVVLRQ Service Notes 08/01/2011 SR

1827EXLT specifications

The Husqvarna 1827EXLT is a robust snow thrower designed to tackle harsh winter conditions with ease and efficiency. With its powerful engine and advanced features, it promises performance and reliability, making it an ideal choice for homeowners who need to clear driveways, walkways, and large areas of snow.

Equipped with a 272cc Husqvarna engine, the 1827EXLT provides an impressive output, ensuring that it can handle heavy and wet snow without any issues. The engine is designed for easy starting, even in cold weather conditions, making winter maintenance a hassle-free experience.

One of the standout features of the 1827EXLT is its two-stage snow throwing mechanism. This design utilizes an auger to collect snow, which is then propelled by an impeller through the chute. The result is efficient snow removal, where the snow can be thrown up to 33 feet away. This extended throwing distance ensures that you can clear large areas without needing to move snow back into already cleared sections.

The snow thrower boasts a clearing width of 27 inches, making it capable of handling wider paths and driveways in fewer passes. The adjustable skid shoes provide customization to the height at which the machine operates, allowing you to prevent damage to surfaces while effectively clearing snow.

The 1827EXLT also features a friction disc transmission that enables smooth speed changes, ensuring a comfortable operation. With six forward and two reverse gears, users can easily navigate various terrains and adapt to changing conditions.

Furthermore, the snow thrower is designed with user comfort in mind. It features heated grips, which significantly enhance the operator's comfort during prolonged use in cold conditions. The easy-to-use control panel provides quick access to all the essential functions, including chute rotation and deflection controls, enhancing the user's experience.

Durability is another big selling point of the Husqvarna 1827EXLT. Its heavy-duty steel frame and high-strength plastic components ensure long-lasting performance and resistance against wear.

In conclusion, the Husqvarna 1827EXLT is a powerful and reliable snow thrower that combines advanced features and user-friendly technology. It is perfect for those who need a dependable machine to keep their outdoor spaces clear during winter, ensuring practicality and efficiency in snow removal tasks. Whether dealing with heavy snowfalls or light dustings, the 1827EXLT stands ready to handle the job.
Top Page Image Contents