Husqvarna 96193005700, 1830SB manual Snow Throwing Tips, To Start Engine, Before Stopping

Page 13

OPERATION

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Move choke control to “FULL” position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

NOTE: Do not use primer when starting engine with the electric starter.

6. Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

7.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

8.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 1830SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Check Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYAuger control lever used to engage auger motion throw snow Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Release the auger control lever and shut off the engineBefore Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigRemove the klik pin and remove wheel from axle CarburetorOther StorageFuel System Engine OILTroubleshooting Service Notes Service Notes Service Notes 532 43 56-27 04.21.10 JA Warranty Statement

96193005700, 1830SB specifications

The Husqvarna 1830SB is a powerful snowblower designed to tackle the challenges of winter weather. Engineered for efficiency, durability, and ease of use, this model is ideal for homeowners with medium to large driveways, pathways, and outdoor spaces that require effective snow removal.

One of the standout features of the Husqvarna 1830SB is its 18-inch clearing width, allowing it to clear large areas more quickly than many other models on the market. Coupled with a 30-inch intake height, this snowblower can handle deep snow with ease, making it a reliable companion during heavy snowfall events.

The Husqvarna 1830SB is equipped with a powerful 342cc engine, providing ample power to drive the auger and impeller system effectively. This engine is designed to start reliably in cold temperatures, ensuring that users can operate the machine even in harsh winter conditions. The snowblower also features electric start functionality, further enhancing convenience for users who may struggle with traditional pull-start engines.

Another key characteristic of the 1830SB is its robust auger and impeller system, which excels at breaking up and propelling snow. The auger quickly retrieves snow from the ground, while the high-speed impeller efficiently casts snow to a distance of up to 35 feet. This feature ensures that both light and heavy snow can be thrown far from the cleared area, preventing snow buildup and allowing for quick status returns to the driveway or pathway.

The snowblower's adjustable drift cutters are an innovative feature that helps to effectively manage heavy, compacted snow, while the integrated LED lights increase visibility during early mornings or late evenings. The 180-degree adjustable chute allows users to direct the snow precisely where they want it, offering optimal control over the snow removal process.

Additionally, the Husqvarna 1830SB includes an easy-to-use control panel, which features simple handling options for speed and direction, making it user-friendly for both experienced operators and those new to snowblowing.

Constructed with a solid steel frame and high-quality materials, the Husqvarna 1830SB promises both reliability and longevity, ensuring it remains a staple in winter maintenance for years to come. Designed to meet the demands of tough winter conditions, the Husqvarna 1830SB stands out as a durable and efficient snow removal solution.
Top Page Image Contents