Husqvarna 1830SB, 96193005700 manual Install Auger Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1.Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end.

2.Hook end of spring into control arm with loop opening up as shown. (See Fig. 5)

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

VINYL

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

AUGER CONTROL ROD

AUGER

RETAINER

CONTROL

LEVER

SPRING

 

 

AUGER

CONTROL

BRACKET

FIG. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotater head over chute bracket. If neces- sary, rotate chute assembly to align square and pin on un- derside of chute rotater head with holes in chute bracket.

3.With chute rotater head and chute bracket aligned, position chute rotater head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE

 

 

ROTATER

 

3/8 LOCKNUT

HEAD

 

 

 

 

3/8 WASHER

 

 

PIN

 

 

THREADED

 

 

STUD

 

ALIGN BEFORE

ROTATER HEAD

CHUTE

MOUNTING

BRACKET

TIGHTENING LOCKNUT

BRACKET

FIG. 7

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Cable eyelet will be loose on shoulder bolt.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 1830SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Auger control lever used to engage auger motion throw snowTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Release the auger control lever and shut off the engineBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Remove the klik pin and remove wheel from axle To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorFuel System StorageOther Engine OILTroubleshooting Service Notes Service Notes Service Notes Warranty Statement 532 43 56-27 04.21.10 JA

96193005700, 1830SB specifications

The Husqvarna 1830SB is a powerful snowblower designed to tackle the challenges of winter weather. Engineered for efficiency, durability, and ease of use, this model is ideal for homeowners with medium to large driveways, pathways, and outdoor spaces that require effective snow removal.

One of the standout features of the Husqvarna 1830SB is its 18-inch clearing width, allowing it to clear large areas more quickly than many other models on the market. Coupled with a 30-inch intake height, this snowblower can handle deep snow with ease, making it a reliable companion during heavy snowfall events.

The Husqvarna 1830SB is equipped with a powerful 342cc engine, providing ample power to drive the auger and impeller system effectively. This engine is designed to start reliably in cold temperatures, ensuring that users can operate the machine even in harsh winter conditions. The snowblower also features electric start functionality, further enhancing convenience for users who may struggle with traditional pull-start engines.

Another key characteristic of the 1830SB is its robust auger and impeller system, which excels at breaking up and propelling snow. The auger quickly retrieves snow from the ground, while the high-speed impeller efficiently casts snow to a distance of up to 35 feet. This feature ensures that both light and heavy snow can be thrown far from the cleared area, preventing snow buildup and allowing for quick status returns to the driveway or pathway.

The snowblower's adjustable drift cutters are an innovative feature that helps to effectively manage heavy, compacted snow, while the integrated LED lights increase visibility during early mornings or late evenings. The 180-degree adjustable chute allows users to direct the snow precisely where they want it, offering optimal control over the snow removal process.

Additionally, the Husqvarna 1830SB includes an easy-to-use control panel, which features simple handling options for speed and direction, making it user-friendly for both experienced operators and those new to snowblowing.

Constructed with a solid steel frame and high-quality materials, the Husqvarna 1830SB promises both reliability and longevity, ensuring it remains a staple in winter maintenance for years to come. Designed to meet the demands of tough winter conditions, the Husqvarna 1830SB stands out as a durable and efficient snow removal solution.
Top Page Image Contents