Husqvarna 96193005700, 1830SB manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 22)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6. REMOVE AUGER BELT from around pulley.

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

12.Install the two (2) hex bolts and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

BOLT

IDLER ARM

AUGER

SQUARE

BELT

HOLE

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

FIG. 22

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 1830SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Chute Deflector Remote Control See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Check Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYAuger control lever used to engage auger motion throw snow Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Release the auger control lever and shut off the engineBefore Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigRemove the klik pin and remove wheel from axle CarburetorOther StorageFuel System Engine OILTroubleshooting Service Notes Service Notes Service Notes 532 43 56-27 04.21.10 JA Warranty Statement

96193005700, 1830SB specifications

The Husqvarna 1830SB is a powerful snowblower designed to tackle the challenges of winter weather. Engineered for efficiency, durability, and ease of use, this model is ideal for homeowners with medium to large driveways, pathways, and outdoor spaces that require effective snow removal.

One of the standout features of the Husqvarna 1830SB is its 18-inch clearing width, allowing it to clear large areas more quickly than many other models on the market. Coupled with a 30-inch intake height, this snowblower can handle deep snow with ease, making it a reliable companion during heavy snowfall events.

The Husqvarna 1830SB is equipped with a powerful 342cc engine, providing ample power to drive the auger and impeller system effectively. This engine is designed to start reliably in cold temperatures, ensuring that users can operate the machine even in harsh winter conditions. The snowblower also features electric start functionality, further enhancing convenience for users who may struggle with traditional pull-start engines.

Another key characteristic of the 1830SB is its robust auger and impeller system, which excels at breaking up and propelling snow. The auger quickly retrieves snow from the ground, while the high-speed impeller efficiently casts snow to a distance of up to 35 feet. This feature ensures that both light and heavy snow can be thrown far from the cleared area, preventing snow buildup and allowing for quick status returns to the driveway or pathway.

The snowblower's adjustable drift cutters are an innovative feature that helps to effectively manage heavy, compacted snow, while the integrated LED lights increase visibility during early mornings or late evenings. The 180-degree adjustable chute allows users to direct the snow precisely where they want it, offering optimal control over the snow removal process.

Additionally, the Husqvarna 1830SB includes an easy-to-use control panel, which features simple handling options for speed and direction, making it user-friendly for both experienced operators and those new to snowblowing.

Constructed with a solid steel frame and high-quality materials, the Husqvarna 1830SB promises both reliability and longevity, ensuring it remains a staple in winter maintenance for years to come. Designed to meet the demands of tough winter conditions, the Husqvarna 1830SB stands out as a durable and efficient snow removal solution.
Top Page Image Contents