Husqvarna 11527SB, 96193006400 manual To Replace Belts See Fig

Page 16

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 20)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6. REMOVE AUGER BELT from around pulley.

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

12.Install the two (2) hex bolts and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

BOLT

IDLER ARM

AUGER

SQUARE

BELT

HOLE

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

FIG. 20

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 11527SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Throttle Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightShear Bolts See Fig To Remove Belt Cover See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission 532 43 58-82 06.23.10 TH

96193006400, 11527SB specifications

The Husqvarna 96193006400, also known as the 11527SB, is a top-tier landscape maintenance tool that caters to both professional landscapers and dedicated homeowners. This robust brush cutter is designed for the toughest of tasks, offering a perfect blend of power, performance, and versatility.

One of the standout features of the Husqvarna 11527SB is its powerful engine. It is equipped with a high-performance 27cc 2-cycle engine that delivers ample power for tackling thick brush and overgrown vegetation. This engine is designed to provide high torque at low RPM, ensuring efficient cutting without the need for frequent refueling.

The machine also boasts an ergonomic design that enhances user comfort. It features adjustable handlebars that allow users to customize the gripping position, significantly reducing fatigue during extended use. Additionally, the anti-vibration technology integrated into the handlebars minimizes vibrations, offering a smoother operation and less strain on the operator’s hands and arms.

Another significant characteristic of the Husqvarna 11527SB is its versatile cutting capability. It comes with a dual-line cutting system that provides excellent performance for trimming grass as well as clearing thick brush. Users can easily switch between different cutting attachments, enhancing the machine's adaptability for various tasks. Whether you need to trim around flower beds or clear out dense vegetation, this brush cutter can handle it all.

The product incorporates advanced technologies that improve its overall efficiency and ease of use. The Smart Start feature reduces the effort needed to start the engine, allowing for a quick and hassle-free ignition every time. This technology, combined with a fuel pump that primes the carburetor, ensures reliable starting even after prolonged periods of inactivity.

Maintenance is also simplified thanks to an effective air filtration system that extends the life of the engine by reducing the amount of dust and debris that gets into the combustion chamber. The user-friendly design includes easy access to the air filter and spark plug, making routine maintenance tasks straightforward for users.

In summary, the Husqvarna 96193006400, 11527SB, is a well-rounded brush cutter that harnesses power, comfort, and innovation. With its robust engine, ergonomic design, versatile cutting options, and advanced technologies, it stands out as an ideal solution for anyone needing professional-grade performance in landscape maintenance.
Top Page Image Contents