Husqvarna 96193006400, 11527SB manual Troubleshooting

Page 19

TROUBLESHOOTING

See appropriate section in manual unless directed to an authorized service center/department.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Fill fuel tank with fresh, clean gasoline.

 

4.

Throttle in STOP position

4.

Move throttle to FAST position

 

 

(or ON/OFF switch is OFF).

 

(or ON/OFF switch to ON position).

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact an authorized service center/department.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts. If vibration

vibration

 

augers or impeller.

 

remains, contact an authorized service center/department.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact an authorized service center/department.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 11527SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Throttle Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningTo Remove Belt Cover See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission 532 43 58-82 06.23.10 TH

96193006400, 11527SB specifications

The Husqvarna 96193006400, also known as the 11527SB, is a top-tier landscape maintenance tool that caters to both professional landscapers and dedicated homeowners. This robust brush cutter is designed for the toughest of tasks, offering a perfect blend of power, performance, and versatility.

One of the standout features of the Husqvarna 11527SB is its powerful engine. It is equipped with a high-performance 27cc 2-cycle engine that delivers ample power for tackling thick brush and overgrown vegetation. This engine is designed to provide high torque at low RPM, ensuring efficient cutting without the need for frequent refueling.

The machine also boasts an ergonomic design that enhances user comfort. It features adjustable handlebars that allow users to customize the gripping position, significantly reducing fatigue during extended use. Additionally, the anti-vibration technology integrated into the handlebars minimizes vibrations, offering a smoother operation and less strain on the operator’s hands and arms.

Another significant characteristic of the Husqvarna 11527SB is its versatile cutting capability. It comes with a dual-line cutting system that provides excellent performance for trimming grass as well as clearing thick brush. Users can easily switch between different cutting attachments, enhancing the machine's adaptability for various tasks. Whether you need to trim around flower beds or clear out dense vegetation, this brush cutter can handle it all.

The product incorporates advanced technologies that improve its overall efficiency and ease of use. The Smart Start feature reduces the effort needed to start the engine, allowing for a quick and hassle-free ignition every time. This technology, combined with a fuel pump that primes the carburetor, ensures reliable starting even after prolonged periods of inactivity.

Maintenance is also simplified thanks to an effective air filtration system that extends the life of the engine by reducing the amount of dust and debris that gets into the combustion chamber. The user-friendly design includes easy access to the air filter and spark plug, making routine maintenance tasks straightforward for users.

In summary, the Husqvarna 96193006400, 11527SB, is a well-rounded brush cutter that harnesses power, comfort, and innovation. With its robust engine, ergonomic design, versatile cutting options, and advanced technologies, it stands out as an ideal solution for anyone needing professional-grade performance in landscape maintenance.
Top Page Image Contents