Husqvarna 11527SB, 96193006400 manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent acci- dental starting when setting up, trans- porting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot en- gine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refuel- ing is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller housing or discharge chute, and when making any

2

repairs, adjustments or inspections.

 

Page 1 Page 3
Image 2
Page 1 Page 3
Contents 11527SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Throttle Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Belt Cover See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission 532 43 58-82 06.23.10 TH

96193006400, 11527SB specifications

The Husqvarna 96193006400, also known as the 11527SB, is a top-tier landscape maintenance tool that caters to both professional landscapers and dedicated homeowners. This robust brush cutter is designed for the toughest of tasks, offering a perfect blend of power, performance, and versatility.

One of the standout features of the Husqvarna 11527SB is its powerful engine. It is equipped with a high-performance 27cc 2-cycle engine that delivers ample power for tackling thick brush and overgrown vegetation. This engine is designed to provide high torque at low RPM, ensuring efficient cutting without the need for frequent refueling.

The machine also boasts an ergonomic design that enhances user comfort. It features adjustable handlebars that allow users to customize the gripping position, significantly reducing fatigue during extended use. Additionally, the anti-vibration technology integrated into the handlebars minimizes vibrations, offering a smoother operation and less strain on the operator’s hands and arms.

Another significant characteristic of the Husqvarna 11527SB is its versatile cutting capability. It comes with a dual-line cutting system that provides excellent performance for trimming grass as well as clearing thick brush. Users can easily switch between different cutting attachments, enhancing the machine's adaptability for various tasks. Whether you need to trim around flower beds or clear out dense vegetation, this brush cutter can handle it all.

The product incorporates advanced technologies that improve its overall efficiency and ease of use. The Smart Start feature reduces the effort needed to start the engine, allowing for a quick and hassle-free ignition every time. This technology, combined with a fuel pump that primes the carburetor, ensures reliable starting even after prolonged periods of inactivity.

Maintenance is also simplified thanks to an effective air filtration system that extends the life of the engine by reducing the amount of dust and debris that gets into the combustion chamber. The user-friendly design includes easy access to the air filter and spark plug, making routine maintenance tasks straightforward for users.

In summary, the Husqvarna 96193006400, 11527SB, is a well-rounded brush cutter that harnesses power, comfort, and innovation. With its robust engine, ergonomic design, versatile cutting options, and advanced technologies, it stands out as an ideal solution for anyone needing professional-grade performance in landscape maintenance.
Top Page Image Contents