Husqvarna 11527SB, 96193006400 manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 18

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 11527SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Throttle Control See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Belt Cover See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission 532 43 58-82 06.23.10 TH

96193006400, 11527SB specifications

The Husqvarna 96193006400, also known as the 11527SB, is a top-tier landscape maintenance tool that caters to both professional landscapers and dedicated homeowners. This robust brush cutter is designed for the toughest of tasks, offering a perfect blend of power, performance, and versatility.

One of the standout features of the Husqvarna 11527SB is its powerful engine. It is equipped with a high-performance 27cc 2-cycle engine that delivers ample power for tackling thick brush and overgrown vegetation. This engine is designed to provide high torque at low RPM, ensuring efficient cutting without the need for frequent refueling.

The machine also boasts an ergonomic design that enhances user comfort. It features adjustable handlebars that allow users to customize the gripping position, significantly reducing fatigue during extended use. Additionally, the anti-vibration technology integrated into the handlebars minimizes vibrations, offering a smoother operation and less strain on the operator’s hands and arms.

Another significant characteristic of the Husqvarna 11527SB is its versatile cutting capability. It comes with a dual-line cutting system that provides excellent performance for trimming grass as well as clearing thick brush. Users can easily switch between different cutting attachments, enhancing the machine's adaptability for various tasks. Whether you need to trim around flower beds or clear out dense vegetation, this brush cutter can handle it all.

The product incorporates advanced technologies that improve its overall efficiency and ease of use. The Smart Start feature reduces the effort needed to start the engine, allowing for a quick and hassle-free ignition every time. This technology, combined with a fuel pump that primes the carburetor, ensures reliable starting even after prolonged periods of inactivity.

Maintenance is also simplified thanks to an effective air filtration system that extends the life of the engine by reducing the amount of dust and debris that gets into the combustion chamber. The user-friendly design includes easy access to the air filter and spark plug, making routine maintenance tasks straightforward for users.

In summary, the Husqvarna 96193006400, 11527SB, is a well-rounded brush cutter that harnesses power, comfort, and innovation. With its robust engine, ergonomic design, versatile cutting options, and advanced technologies, it stands out as an ideal solution for anyone needing professional-grade performance in landscape maintenance.
Top Page Image Contents