Husqvarna 12530HV warranty Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

Thechutedeflector,attachedtothetopofthedischargechute, is provided to direct discharging snow away from the opera- tor. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 20)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shear bolt and hex nut. Should a foreign ob- ject or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

 

The impeller is secured to the impeller shaft with two (2)

 

capscrew/shear bolts and hex nuts. Should a foreign object

 

or ice become lodged in the impeller, the capscrews are

 

designed to break, preventing damage to any other com-

 

ponents. If impeller does not turn when auger control lever

 

is engaged, check to see if the capscrews have sheared.

16

To replace the capscrew/shear bolts:

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20 x 1-5/8

1/4-20 x 2

CAPSCREW /

SHOULDER /

SHEAR BOLT

SHEAR BOLT

IMPELLER

 

HUB

 

1/4-20

 

LOCKNUT

 

 

AUGER HUB

 

1/4-20 LOCKNUT

 

AUGER

 

SHAFT

 

IMPELLER

 

SHAFT

FIG. 20

TO REMOVE BELT COVER (See Fig. 21)

1.Loosen the two (2) screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and tightening screws.

 

BELT

 

COVER

FRAME

SCREWS

FIG. 21

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 115 61 Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Carriage BoltsAssembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance ➀ SAE 30 Motor Oil ➁ See Engine Maintenance sectionGeneral Recommendations Before Each USESnow Thrower CleaningEngine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Adjust Traction Belt and Auger Belt TensionTo Remove Wheels See Fig CarburetorStorage OtherFuel System Engine OILTroubleshooting Problem Cause CorrectionService Notes Service Notes Service Notes Consumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below 07/01/2013 TH

12530HV specifications

The Husqvarna 12530HV is a versatile and efficient lawn mower that combines performance with innovative technology, designed to meet the needs of both residential and commercial users. With its lightweight yet sturdy design, the 12530HV stands out in the market for its user-friendly features and advanced functionalities, making lawn maintenance a breeze.

One of the key features of the Husqvarna 12530HV is its powerful engine. Equipped with a robust 30cc engine, this mower boasts a high power-to-weight ratio, ensuring it can tackle even the toughest grass and terrain with ease. The engine is designed for efficiency, providing reliable performance while minimizing fuel consumption.

The ergonomic design of the 12530HV enhances user comfort and control. The adjustable handle allows users to find the perfect height for mowing, reducing strain during extended use. Furthermore, the soft grip adds an extra layer of comfort for the operator, making long mowing sessions more enjoyable.

One of the standout technologies integrated into the Husqvarna 12530HV is its advanced cutting system. Featuring a variable speed option, this mower allows users to adjust the cutting speed according to the grass conditions, ensuring an optimal cut every time. The heavy-duty cutting deck is designed for durability, featuring high-quality blades that deliver precision cuts and a clean finish.

Another notable characteristic is the mower's high-capacity grass bag. Its ample size allows for extended mowing sessions without frequent stops for emptying, which is particularly beneficial for larger lawns. The bag is designed for easy attachment and removal, streamlining the mowing process.

Safety is a priority with the Husqvarna 12530HV. It comes equipped with a safety switch that ensures the engine stops when the user releases the handle, preventing accidental injuries. This feature, combined with the mower's stability and control, makes it a reliable choice for users of all experience levels.

Overall, the Husqvarna 12530HV is an excellent choice for those seeking a powerful, efficient, and user-friendly lawn mower. With its combination of advanced features, innovative technologies, and a focus on comfort and safety, it is well-equipped to handle a variety of mowing tasks, providing exceptional results with minimal effort. Whether for residential or commercial use, this mower is designed to deliver a superior mowing experience.
Top Page Image Contents