Husqvarna 12530HV warranty To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 22)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.

REMOVE HAIRPIN FROM CLUTCH ROD and re-

 

move clutch rod from swing plate. Tip swing plate

 

forward.

7.

REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

BOLT

IDLER ARM

AUGER

SQUARE

BELT

HOLE

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

17

FIG. 22

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 115 61 Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Carriage Bolts Parts Packed Separately in CartonHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen➀ SAE 30 Motor Oil ➁ See Engine Maintenance section MaintenanceGeneral Recommendations Before Each USEEngine CleaningSnow Thrower To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Traction Belt and Auger Belt Tension To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorOther StorageFuel System Engine OILProblem Cause Correction TroubleshootingService Notes Service Notes Service Notes Consumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below 07/01/2013 TH

12530HV specifications

The Husqvarna 12530HV is a versatile and efficient lawn mower that combines performance with innovative technology, designed to meet the needs of both residential and commercial users. With its lightweight yet sturdy design, the 12530HV stands out in the market for its user-friendly features and advanced functionalities, making lawn maintenance a breeze.

One of the key features of the Husqvarna 12530HV is its powerful engine. Equipped with a robust 30cc engine, this mower boasts a high power-to-weight ratio, ensuring it can tackle even the toughest grass and terrain with ease. The engine is designed for efficiency, providing reliable performance while minimizing fuel consumption.

The ergonomic design of the 12530HV enhances user comfort and control. The adjustable handle allows users to find the perfect height for mowing, reducing strain during extended use. Furthermore, the soft grip adds an extra layer of comfort for the operator, making long mowing sessions more enjoyable.

One of the standout technologies integrated into the Husqvarna 12530HV is its advanced cutting system. Featuring a variable speed option, this mower allows users to adjust the cutting speed according to the grass conditions, ensuring an optimal cut every time. The heavy-duty cutting deck is designed for durability, featuring high-quality blades that deliver precision cuts and a clean finish.

Another notable characteristic is the mower's high-capacity grass bag. Its ample size allows for extended mowing sessions without frequent stops for emptying, which is particularly beneficial for larger lawns. The bag is designed for easy attachment and removal, streamlining the mowing process.

Safety is a priority with the Husqvarna 12530HV. It comes equipped with a safety switch that ensures the engine stops when the user releases the handle, preventing accidental injuries. This feature, combined with the mower's stability and control, makes it a reliable choice for users of all experience levels.

Overall, the Husqvarna 12530HV is an excellent choice for those seeking a powerful, efficient, and user-friendly lawn mower. With its combination of advanced features, innovative technologies, and a focus on comfort and safety, it is well-equipped to handle a variety of mowing tasks, providing exceptional results with minimal effort. Whether for residential or commercial use, this mower is designed to deliver a superior mowing experience.
Top Page Image Contents