Husqvarna 12530HV warranty To Remove Wheels See Fig, Carburetor, Engine Speed

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 23)

•Remove the wheel pin and retainer pin and remove wheel from axle.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

SEE ENGINE MANUAL.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 2,134 meters. If your engine does not operate properly due to suspected

WHEEL PIN (INSTALL IN OUTER HOLE OF AXLE ONLY)

RETAINER

PIN

OUTER HOLE

AXLE

carburetor problems, take your snow thrower to a service center/department.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a service center/depart- ment, which has the proper equipment and experience to

WHEEL

WHEEL HUB

FIG. 23

TO ADJUST CABLE TENSION (See Fig. 24)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 24

TO ADJUST TRACTION BELT AND AUGER BELT TENSION

If the traction or auger belt is slipping because it is not tight enough when engaged, the tension can be increased by adjusting the spring location in the control rod. Unhook the rod from the control lever and move the spring at the bottom of the rod one or two holes closer to the top of the rod. This effectively shortens the rod and increases the belt tension. (See "INSTALL AUGER CONTROL ROD" in the Assembly section of this manual.)

make any necessary adjustments.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 115 61 Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Carriage BoltsRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenGeneral Recommendations Maintenance➀ SAE 30 Motor Oil ➁ See Engine Maintenance section Before Each USECleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigTo Adjust Traction Belt and Auger Belt Tension CarburetorFuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionService Notes Service Notes Service Notes Consumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below 07/01/2013 TH

12530HV specifications

The Husqvarna 12530HV is a versatile and efficient lawn mower that combines performance with innovative technology, designed to meet the needs of both residential and commercial users. With its lightweight yet sturdy design, the 12530HV stands out in the market for its user-friendly features and advanced functionalities, making lawn maintenance a breeze.

One of the key features of the Husqvarna 12530HV is its powerful engine. Equipped with a robust 30cc engine, this mower boasts a high power-to-weight ratio, ensuring it can tackle even the toughest grass and terrain with ease. The engine is designed for efficiency, providing reliable performance while minimizing fuel consumption.

The ergonomic design of the 12530HV enhances user comfort and control. The adjustable handle allows users to find the perfect height for mowing, reducing strain during extended use. Furthermore, the soft grip adds an extra layer of comfort for the operator, making long mowing sessions more enjoyable.

One of the standout technologies integrated into the Husqvarna 12530HV is its advanced cutting system. Featuring a variable speed option, this mower allows users to adjust the cutting speed according to the grass conditions, ensuring an optimal cut every time. The heavy-duty cutting deck is designed for durability, featuring high-quality blades that deliver precision cuts and a clean finish.

Another notable characteristic is the mower's high-capacity grass bag. Its ample size allows for extended mowing sessions without frequent stops for emptying, which is particularly beneficial for larger lawns. The bag is designed for easy attachment and removal, streamlining the mowing process.

Safety is a priority with the Husqvarna 12530HV. It comes equipped with a safety switch that ensures the engine stops when the user releases the handle, preventing accidental injuries. This feature, combined with the mower's stability and control, makes it a reliable choice for users of all experience levels.

Overall, the Husqvarna 12530HV is an excellent choice for those seeking a powerful, efficient, and user-friendly lawn mower. With its combination of advanced features, innovative technologies, and a focus on comfort and safety, it is well-equipped to handle a variety of mowing tasks, providing exceptional results with minimal effort. Whether for residential or commercial use, this mower is designed to deliver a superior mowing experience.
Top Page Image Contents