Husqvarna 8527SBEB owner manual Repair Parts, Control Panel / Discharge Chute

Page 23

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 8527SBEB (96193001100), PRODUCT NO. 961 93 00-11

KEY	PART
NO.	NO.	DESCRIPTION

1532 18 33-34 Knob, Lever

2817 50 10-10 Screw #10-24 x 5/8

3532 19 84-75 Control Assembly, Deﬂector

4873 80 06-00 Nut, Lock 3/8-16

5819 13 13-16 Washer, Flat 3/8

6532 19 84-73 Control Assembly, Chute Rotater

7532 18 40-89 Support, Pivot

8 532 15 00-78 Screw, Hex Head 5/16-18 x 3/4

9532 18 45-05 Spring, Deﬂector

10532 17 98-29 Bolt, Shoulder

11532 17 92-46 Washer, Flat 1/4

12873 80 04-00 Nut, Lock 1/4-20

13872 25 05-05 Bolt, Carriage 5/16-18

14873 80 05-00 Nut, Lock 5/16-18

15532 18 41-12 Chute Assembly

16532 18 41-13 Deﬂector Assembly

17532 17 91-45 Seal, Deﬂector

18532 12 84-15 Rivet, Blind

19532 18 33-33 Knob, Speed Control Lever

20	872 27 05-06	Bolt, Carriage 5/16-18 x 3/4
22	532 15 54-15	Washer, Flat 5/16
24	874 78 05-28	Screw, Hex Head 5/16-18 x 1-3/4

25532 15 53-77 Nut, Lock 5/16-18

26532 19 88-75 Lever Assembly, Speed Control

27532 16 96-75 Retainer, Hairpin

28532 18 04-45 Rod, Upper, Speed Control

29532 18 77-16 Rod, Lower, Speed Control

30532 19 27-10 Clamp, Clean-Out Tool

31532 19 21-99 Tool, Clean-Out

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

23

Image 23

Contents 8527SBEB Operation Safe Operation Practices for Walk-Behind Snow ThrowersTraining PreparationCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS Maintenance and StoragePARTS PACKED SEPARATELY IN CARTON INSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andCHECK TIRE PRESSURE INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and KNOW YOUR SNOW THROWER OPERATIONDrive speed control lever - used to select forward or MEETS A.N.S.I. SAFETY REQUIREMENTSTO USE THROTTLE CONTROL See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE FUEL SHUT-OFF VALVE See FigTO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigCLEAN-OUT TO THROW SNOW See FigCHECK ENGINE OIL LEVEL See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BARIF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSBEFORE STOPPING LUBRICATION MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE V-BELTS3. Make sure the augers and all moving parts have completely stopped SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig CARBURETOR STORAGEOTHER TO REMOVE WHEELS See FigEngine idles or TROUBLESHOOTINGLoss of power Does not startAUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTSSNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY CONTROL PANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO HANDLES HANDLES DRIVE SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO CHASSIS / ENGINE / PULLEYS532 PARTDESCRIPTION 1 13 WHEELS / DECALSWHEELS / DECALS ANR AVSQ UH STATEMENTWARRANTY532 40 37-57 Rev. 1 12.21.05 BY 2002