Husqvarna 8527SBEB owner manual Operation, Meets A.N.S.I. Safety Requirements

Page 9
MEETS A.N.S.I. SAFETY REQUIREMENTS

OPERATION

GASOLINE FILLER CAP

MUFFLER

CHOKE

CON-

TROL

PRIMER

SAFETY IGNITION KEY

ELECTRIC AUGER

START CONTROL

BUTTON LEVER

RECOIL (AUXILIARY)

STARTER

HANDLE

CHUTE DEFLECTOR

DISCHARGE CHUTE CONTROL LEVER

DEFLECTOR REMOTE

DRIVE SPEEDCONTROL LEVER CONTROL LEVER

TRACTION

DRIVE

CONTROL

LEVER

LIGHT

FUEL SHUT-OFF VALVE

THROTTLE / ENGINE CONTROL

DISCHARGE

CHUTE

CLEAN-OUT TOOL

HANDLE KNOB

MUFFLER

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE ENGINE. ACTUAL LOCATION MAY VARY WITH THE ENGINE ON YOUR UNIT.

AUGERS

FIG. 10

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting engine.

 

Primer - pumps additional fuel from the carburetor to the

 

cylinder for use when starting a cold engine.

 

Throttle/engine control - used to select either FAST or

 

SLOW engine speed and to STOP the engine.

 

Drive speed control lever - used to select forward or

 

reverse motion and speed of snow thrower.

9

Choke control - used for starting a cold engine.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Deflector remote control lever - used to change the distance the snow is thrown.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 8527SBEB Training Safe Operation Practices for Walk-Behind Snow ThrowersPreparation OperationPRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON HOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONREMOVE SNOW THROWER FROM CARTON INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andINSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See Fig INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 andCHECK TIRE PRESSURE KNOW YOUR SNOW THROWER OPERATIONDrive speed control lever - used to select forward or MEETS A.N.S.I. SAFETY REQUIREMENTSSTOPPING HOW TO USE YOUR SNOW THROWERTO USE FUEL SHUT-OFF VALVE See Fig TO USE THROTTLE CONTROL See FigCLEAN-OUT USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See FigTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR CHECK ENGINE OIL LEVEL See FigSNOW THROWING TIPS BEFORE STOPPINGIF RECOIL STARTER HAS FROZEN GENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGV-BELTS AUGER GEAR CASE1. Be sure throttle is in STOP position 2. Remove safety ignition key SERVICE AND ADJUSTMENTSTO ADJUST SNOW THROWER HEIGHT 3. Make sure the augers and all moving parts have completely stoppedTO REPLACE BELTS See Fig OTHER STORAGETO REMOVE WHEELS See Fig CARBURETORLoss of power TROUBLESHOOTINGDoes not start Engine idles orREPAIR PARTS SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NOAUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLYSNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO CONTROL PANEL / DISCHARGE CHUTE REPAIR PARTS HANDLES HANDLES DRIVE REPAIR PARTS SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO CHASSIS / ENGINE / PULLEYSPART DESCRIPTION532 1 13 WHEELS / DECALSWHEELS / DECALS 532 40 37-57 Rev. 1 12.21.05 BY STATEMENTWARRANTY2002 ANR AVSQ UH
Top Page Image Contents