Husqvarna 8527SBEB Assembly / Pre-Operation, Remove Snow Thrower From Carton, TOOL BOX See Fig

Page 5
ASSEMBLY / PRE-OPERATION

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 10)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED CONTROL ROD

RETAINER

SPRING

SPEEDSPEED

CONTROL CONTROL

BRACKET LEVER

FIG. 2

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 8527SBEB Training Safe Operation Practices for Walk-Behind Snow ThrowersPreparation OperationPRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON HOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONREMOVE SNOW THROWER FROM CARTON INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andCHECK TIRE PRESSURE INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and KNOW YOUR SNOW THROWER OPERATIONDrive speed control lever - used to select forward or MEETS A.N.S.I. SAFETY REQUIREMENTSSTOPPING HOW TO USE YOUR SNOW THROWERTO USE FUEL SHUT-OFF VALVE See Fig TO USE THROTTLE CONTROL See FigCLEAN-OUT USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See FigTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR CHECK ENGINE OIL LEVEL See FigIF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSBEFORE STOPPING GENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGV-BELTS AUGER GEAR CASE1. Be sure throttle is in STOP position 2. Remove safety ignition key SERVICE AND ADJUSTMENTSTO ADJUST SNOW THROWER HEIGHT 3. Make sure the augers and all moving parts have completely stoppedTO REPLACE BELTS See Fig OTHER STORAGETO REMOVE WHEELS See Fig CARBURETORLoss of power TROUBLESHOOTINGDoes not start Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTSSNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY CONTROL PANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO HANDLES HANDLES DRIVE SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO CHASSIS / ENGINE / PULLEYS532 PARTDESCRIPTION 1 13 WHEELS / DECALSWHEELS / DECALS 532 40 37-57 Rev. 1 12.21.05 BY STATEMENTWARRANTY2002 ANR AVSQ UH
Top Page Image Contents