Husqvarna 8527SBEB owner manual Handles, Repair Parts

Page 25

REPAIR PARTS

 

HANDLES

SNOW THROWER - MODEL NO. 8527SBEB (96193001100), PRODUCT NO. 961 93 00-11

KEY

PART

 

NO.

NO.

DESCRIPTION

1532 18 41-10 Lever, Auger Control, RH

2532 18 41-09 Lever, Traction Drive Control, LH

3532 19 96-39 Nut, Cage 1/4-20

4532 17 88-88 Bushing, Flange

5532 16 96-75 Retainer, Hairpin

6 532 19 96-40 Screw, Hex Head 1/4-20 x 3/4

7532 17 86-52 Rod, Interlock

8532 19 95-76 Arm, Impeller Rod

9532 19 95-75 Arm, Traction Rod

10

532 19 95-31

Panel, Control

11

874 78 05-24

Screw, Hex Head 5/16-18 x 1-1/2

12

874 78 05-28

Screw, Hex Head 5/16-18 x 1-3/4

13532 18 41-07 Handle Tube, LH

14532 18 41-08 Handle Tube, RH

15873 80 05-00 Nut, Lock 5/16-18

16819 13 13-16 Washer, Flat 3/8

17532 17 88-99 Knob, Handle

18532 18 04-80 Rod, Auger Control

19532 19 30-81 Rod, Traction Control

20532 18 04-28 End, Control Rod

21873 35 05-00 Nut, Hex, Jam 5/16-18

22 872 12 06-18 Bolt, Carriage 3/8-16 x 2-1/4

23532 18 40-87 Handle Tube, Lower

24532 18 04-47 Sleeve, Spring

25532 18 09-26 Spring, Traction Drive

26532 17 86-69 Spring, Auger Control

27 871 21 06-16 Screw, Hex Head 3/8-16 x 1

28532 17 53-31 Bushing, Pivot Lever

29532 19 30-72 Screw, Headlight Ground Wire to Blower Housing

30532 18 29-06 Console, Panel

31

532 17 52-62

Screw, Hex Head, Tapping

#10-24 x 1-1/4

32

532 18 44-71

Screw, Hex Head, Tapping

#10-24 x 1/2

33532 19 95-77 Latch, Interlock

34532 18 35-18 Bolt, Shoulder

35532 06 80-38 Nut, Lock 1/4-20

36532 17 88-31 Spring, Torsion

37532 19 38-85 Spring, Interlock

38532 17 86-66 Headlight, Halogen (Includes Bulb)

532 40 16-20 Bulb, Halogen

39532 17 86-68 Bezel, Headlight

40532 18 09-64 Harness, Headlight (Halogen)

41532 17 88-90 Nut, Cage 3/8-16

42532 19 95-78 Lever, Interlock

43532 19 96-38 Rod, Latch, Interlock

44532 19 63-38 Rod, Arm, Interlock

45532 70 02-79 Clip

46532 17 92-46 Washer, Friction

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 8527SBEB Training Safe Operation Practices for Walk-Behind Snow ThrowersPreparation OperationPRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON HOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONREMOVE SNOW THROWER FROM CARTON INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigCHECK TIRE PRESSURE KNOW YOUR SNOW THROWER OPERATIONDrive speed control lever - used to select forward or MEETS A.N.S.I. SAFETY REQUIREMENTSSTOPPING HOW TO USE YOUR SNOW THROWERTO USE FUEL SHUT-OFF VALVE See Fig TO USE THROTTLE CONTROL See FigCLEAN-OUT USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See FigTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR CHECK ENGINE OIL LEVEL See FigBEFORE STOPPING SNOW THROWING TIPSIF RECOIL STARTER HAS FROZEN GENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGV-BELTS AUGER GEAR CASE1. Be sure throttle is in STOP position 2. Remove safety ignition key SERVICE AND ADJUSTMENTSTO ADJUST SNOW THROWER HEIGHT 3. Make sure the augers and all moving parts have completely stoppedTO REPLACE BELTS See Fig OTHER STORAGETO REMOVE WHEELS See Fig CARBURETORLoss of power TROUBLESHOOTINGDoes not start Engine idles orSNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY AUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTSSNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO CONTROL PANEL / DISCHARGE CHUTE CONTROL PANEL / DISCHARGE CHUTE HANDLES HANDLES DRIVE DRIVE SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO CHASSIS / ENGINE / PULLEYSDESCRIPTION PART532 1 13 WHEELS / DECALSWHEELS / DECALS 532 40 37-57 Rev. 1 12.21.05 BY STATEMENTWARRANTY2002 ANR AVSQ UH
Top Page Image Contents